Re: cleaner wiring solution needed

[Crash Gordon® <NONE@xxxxxxxx>]

Sheesh, that was a nasty one.


"Jackcsg" <nospam@xxxxxxxxxx> wrote in message =
news:XM2dnXEhb54g3t7fRVn-sw@xxxxxxxxxxxxxxx
> Personally....I have to go back about 11 years when I did residential. =
I
> honestly can't remember ever selling, or just doing a prewire only. =
But on
> the other hand I do recall going out to a house that was supposedly
> pre-wired by another dealer, and the new homeowners elected not to =
spend the
> other $1,200 bucks to have the system installed. It was a referral =
from one
> of my existing customers. When I got to the house, the homeowner =
stated that
> the entire house had been pre-wired, and he just needed the devices
> installed. Knowing how wonderful a typical installation (Residential)
> Company here in Maryland does things...I decided to dig deeper, and =
just
> make certain they did a good job, and I wasn't going to get screwed. =
Holy
> shit! These idiot's put the control panel up in the first floor hall =
closet,
> (no big deal). When I opened the hall closet, sure as shit, there's =
about 18
> to 20 some-odd wires all coiled up pretty as can be. Then I decided to =
go
> down into the basement, and have a look at the wiring job. That's =
where it
> ended. I couldn't see any wire what-so-ever, none. I poked around, and =
I
> could see the bundle of wires going up through the floor to the front =
hall
> closet, but they ran over an HVAC duct, and then disappeared. I went =
to my
> truck, grabbed a latter, looked up on top of the duct....there's a =
coil of
> wire all rolled up sitting on the duct. About 15 feet of 18 to 20 =
wires
> going to nowhere....They even drilled the windows out, and the doors, =
and
> even placed the contacts in them....but ran not one single wire to =
them, or
> any of the devices. At first glance from the hall closet, this house =
was
> wired to the hilt. The homeowner sued the Builder for $4,000 dollars, =
got
> his $800.00 dollars back from the alarm company, and I put a $1,800 =
dollar
> system in.
> I guess the moral would be....don't deal with the pre-wire, if you =
don't
> have the entire system.
> Most Builders are cheap bastards, and ALL eventually will screw you =
one way
> or another.
> Deal directly with the Homeowner, whenever possible.
>=20
>=20
> "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message
> news:NsG0e.35$j27.907@xxxxxxxxxxxxxxxxxx
> ....and should I care? Do we have to cater to the lowest-common =
denominator
> when installing or can we install per our design preferences?...see =
what I'm
> saying? Whaddya think?
>=20
>=20
> "Jackcsg" <nospam@xxxxxxxxxx> wrote in message
> news:V6idnYUvPbosAN_fRVn-2g@xxxxxxxxxxxxxxx
> > Crash....start wiring a few zones back to some keypad locations. =
There's
> > always the 790 keypad. It should even cut down on the amount of wire =
you
> > have to pull back to the can.
> > ;-)
> >
> > "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message
> > news:PFp0e.62$pA4.618@xxxxxxxxxxxxxxxxxx
> > I don't give it away to the builder...its just that with a custom =
spec the
> > builder never know when hes gonna sell it and to whom, sure we get a =
good
> > portion of the trims, but then some jerk puts in his own Skylink or =
some
> joe
> > schmoe comes along and puts in a 4 zone panel in a house that needs =
20
> > zones...etc.
> >
> >
> > "alarman" <alarman2000@xxxxxxxxx> wrote in message
> > news:UVo0e.608$Mt5.355@xxxxxxxxxxxxx
> > > Crash Gordon=AE wrote:
> > > > kinda why I'm asking for opinions...these days all the houses =
I've
> > > > been doing are 5000 sq+ and the wire cost and labor is killing
> > > > me...to stay at a reasonable price to the builder (or custom =
builder)
> > > > it would be much more cost effective to use addressable stuff =
and
> > > > prewire for that.
> > > >
> > > > some of the customs are 'spec' houses, so we don't get contact =
with
> > > > the h/o until the drywall is up...or later.
> > > >
> > > > i'm bidding a 5400 sq ft one right now, the freekin ceilings are =
16'
> > >
> > > I stopped giving it away on those monsters. I figure my real costs =
and
> > labor
> > > at $75/hr plus. If the builder wants it cheaper, he can get out =
the
> yellow
> > > pages. Nobody is building their million dollar house on my back, =
not
> > > anymore. I found a select few builders who are willing to pay. No =
short
> > > cuts. I take my time and make the wiring neat. I use drive rings. =
I
> drill
> > my
> > > own goddamned holes, and use the right wire for each application, =
not
> 22/4
> > > for everything. Lots of extra wiring for future possibles. No =
banjo
> > strings
> > > in the attic. No ragged holes in their door jambs.
> > > js
> > >
> > >
> > >
> >
> >
>=20
>=20
>