Re: NEED HELP SAFEWATCH PRO 3000EN

["." <.@xxxxxxxxx>]

Ok, How do I go thru the entries and what an I looking for?

"Crash Gordon®" <NONE@xxxxxxxx> wrote in message
news:eKi6e.63$yB.768@xxxxxxxxxxxxxxxxxx
Yes. Thats sounds like you're in programming.

9 points + 2 keyfobs... the keyfobs take up zones you know...you'd have know
how many buttons on each keyfob are being used.

SA5882 is a Canadian part number for 5881..but I can't remember how many
zones it would handle....lemme check. If it's 16 you are gonna close.
5881L=8, 5881M=16, 5881H=32..

You may want to, in the mean time, go through each programming field with
#20, #21...etc. and write down all the entries that are in there now on a
programming sheet...so if  you mess up at least you have a record of what
was there.

*99 to get out of programming.






"." <.@xxxxxxxxx> wrote in message
news:NZg6e.52126$vK6.50876@xxxxxxxxxxxxxxxxxxxxxxxxx
> There are eight points, one motion, and 2 key fobs.
> I have an installer code, however you know when you told me that I use
> (Then
> just go into programming, Installer Code + Code 00, then to %56 to add the
> xtmr.)  That does not get me into the programming mode.  I can get into it
> where it says Field? and then goto *56, it then says: SET TO CONFIRM?
> Is that the same place?
>
> I am still trying to find the model number of the reciever I found
> something
> SA5882??
>
>
> "Crash Gordon®" <NONE@xxxxxxxx> wrote in message
> news:6gd6e.10$4z4.737@xxxxxxxxxxxxxxxxxx
> That'd be 6160V (V for Voice...I think). Yes, you can program with that
> one
> (99% sure anyway...I've not used that one). But you will know for certain
> when you get to *56 field which is where the zone programming begins...if
> it
> doesn't say "Field?" then you can't use it...but pretty sure you can.
>
> So what kind of reciever does it have and how many wireless points are you
> currently using? Including keyfobs or wireless keypads (like 5800BD) if
> any?
>
> Do you know the Installer Code?
> Is it monitored by ADT still?
>
>
>
>
>
> "." <.@xxxxxxxxx> wrote in message
> news:zzc6e.49288$f%4.14586@xxxxxxxxxxxxxxxxxxxxxxxxx
> > Here is a picture of the case, there are two numbers listed.  One on a
> > sticker that reads 6160V ADT, the other is stamped on the plastic it
> > reads
> > M6924, whick one is the model # ?
> > "Crash Gordon®" <NONE@xxxxxxxx> wrote in message
> > news:Ynb6e.2$yB.104@xxxxxxxxxxxxxxxxxx
> > Of what, the keypad?...you'd have to open it up..or describe it
> > here...or
> > go
> > to Ademco's website and see if you can match it up with a pix there. The
> > model number is not usually on the keypad..its usually inside on the
> > board.
> > ADT's numbers will be the same as Ademco's.
> >
> > The reciever model is on the reciever's board, open the can - the
> > reciever
> > is the circuit board above the main board the model number is part of
> > the
> > circuit board traces (top middle). If there is no reciever in the can,
> > and
> > you DO have wireless points on the system, you may have a keypad with RF
> > reciever  built into it.
> >
> > BTW... IF you are still monitored by ADT do NOT mess with it...you
> > probably
> > can't if you are still monitored anyway.
> >
> >
> >
> >
> > "." <jpmk@xxxxxxxxxxxxx> wrote in message
> > news:Yx36e.37119$UW6.35553@xxxxxxxxxxxxxxxxxxxxxxxxx
> > > Where would you find the model number?
> > >
> > > "Crash Gordon®" <NONE@xxxxxxxx> wrote in message
> > > news:YS06e.789$AV3.1393@xxxxxxxxxxxxxxxxxx
> > > It's the same as Vista 20P (pretty much).
> > >
> > > You'll need a programming keypad 6139 etc.
> > >
> > > You need to know if you have any room left on the reciever...check the
> > > receiver model #...is it a 5881L, 5881M, 5881H. Also, how many xtmrs
> > > are
> > > on
> > > it now..including any keyfobs, pirs, gbs, wireless smokes, etc.
> > >
> > > Then just go into programming, Installer Code + Code 00, then to %56
> > > to
> > > add
> > > the xtmr.
> > >
> > >
> > > "." <jpmk@xxxxxxxxxxxxx> wrote in message
> > > news:K606e.36791$UW6.14989@xxxxxxxxxxxxxxxxxxxxxxxxx
> > > > How does one add a wireless X-mitter.  And where can I get the
> > > > Installer
> > > > manual for this system?
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> >
>
>
>