Re: NEED HELP SAFEWATCH PRO 3000EN

[Crash Gordon® <NONE@xxxxxxxx>]

Yes. Thats sounds like you're in programming.

9 points + 2 keyfobs... the keyfobs take up zones you know...you'd have =
know how many buttons on each keyfob are being used.

SA5882 is a Canadian part number for 5881..but I can't remember how many =
zones it would handle....lemme check. If it's 16 you are gonna close. =
5881L=3D8, 5881M=3D16, 5881H=3D32..=20

You may want to, in the mean time, go through each programming field =
with #20, #21...etc. and write down all the entries that are in there =
now on a programming sheet...so if  you mess up at least you have a =
record of what was there.

*99 to get out of programming.






"." <.@xxxxxxxxx> wrote in message =
news:NZg6e.52126$vK6.50876@xxxxxxxxxxxxxxxxxxxxxxxxx
> There are eight points, one motion, and 2 key fobs.
> I have an installer code, however you know when you told me that I use =
(Then=20
> just go into programming, Installer Code + Code 00, then to %56 to add =
the=20
> xtmr.)  That does not get me into the programming mode.  I can get =
into it=20
> where it says Field? and then goto *56, it then says: SET TO CONFIRM?
> Is that the same place?
>=20
> I am still trying to find the model number of the reciever I found =
something=20
> SA5882??
>=20
>=20
> "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message=20
> news:6gd6e.10$4z4.737@xxxxxxxxxxxxxxxxxx
> That'd be 6160V (V for Voice...I think). Yes, you can program with =
that one=20
> (99% sure anyway...I've not used that one). But you will know for =
certain=20
> when you get to *56 field which is where the zone programming =
begins...if it=20
> doesn't say "Field?" then you can't use it...but pretty sure you can.
>=20
> So what kind of reciever does it have and how many wireless points are =
you=20
> currently using? Including keyfobs or wireless keypads (like 5800BD) =
if any?
>=20
> Do you know the Installer Code?
> Is it monitored by ADT still?
>=20
>=20
>=20
>=20
>=20
> "." <.@xxxxxxxxx> wrote in message=20
> news:zzc6e.49288$f%4.14586@xxxxxxxxxxxxxxxxxxxxxxxxx
> > Here is a picture of the case, there are two numbers listed.  One on =
a
> > sticker that reads 6160V ADT, the other is stamped on the plastic it =
reads
> > M6924, whick one is the model # ?
> > "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message
> > news:Ynb6e.2$yB.104@xxxxxxxxxxxxxxxxxx
> > Of what, the keypad?...you'd have to open it up..or describe it =
here...or=20
> > go
> > to Ademco's website and see if you can match it up with a pix there. =
The
> > model number is not usually on the keypad..its usually inside on the =

> > board.
> > ADT's numbers will be the same as Ademco's.
> >
> > The reciever model is on the reciever's board, open the can - the =
reciever
> > is the circuit board above the main board the model number is part =
of the
> > circuit board traces (top middle). If there is no reciever in the =
can, and
> > you DO have wireless points on the system, you may have a keypad =
with RF
> > reciever  built into it.
> >
> > BTW... IF you are still monitored by ADT do NOT mess with it...you=20
> > probably
> > can't if you are still monitored anyway.
> >
> >
> >
> >
> > "." <jpmk@xxxxxxxxxxxxx> wrote in message
> > news:Yx36e.37119$UW6.35553@xxxxxxxxxxxxxxxxxxxxxxxxx
> > > Where would you find the model number?
> > >
> > > "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message
> > > news:YS06e.789$AV3.1393@xxxxxxxxxxxxxxxxxx
> > > It's the same as Vista 20P (pretty much).
> > >
> > > You'll need a programming keypad 6139 etc.
> > >
> > > You need to know if you have any room left on the reciever...check =
the
> > > receiver model #...is it a 5881L, 5881M, 5881H. Also, how many =
xtmrs are
> > > on
> > > it now..including any keyfobs, pirs, gbs, wireless smokes, etc.
> > >
> > > Then just go into programming, Installer Code + Code 00, then to =
%56 to
> > > add
> > > the xtmr.
> > >
> > >
> > > "." <jpmk@xxxxxxxxxxxxx> wrote in message
> > > news:K606e.36791$UW6.14989@xxxxxxxxxxxxxxxxxxxxxxxxx
> > > > How does one add a wireless X-mitter.  And where can I get the=20
> > > > Installer
> > > > manual for this system?
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> >=20
>=20
>=20
>