[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]
Re: NEED HELP SAFEWATCH PRO 3000EN
That'd be 6160V (V for Voice...I think). Yes, you can program with that =
one (99% sure anyway...I've not used that one). But you will know for =
certain when you get to *56 field which is where the zone programming =
begins...if it doesn't say "Field?" then you can't use it...but pretty =
sure you can.
So what kind of reciever does it have and how many wireless points are =
you currently using? Including keyfobs or wireless keypads (like 5800BD) =
if any?
Do you know the Installer Code?
Is it monitored by ADT still?
"." <.@xxxxxxxxx> wrote in message =
news:zzc6e.49288$f%4.14586@xxxxxxxxxxxxxxxxxxxxxxxxx
> Here is a picture of the case, there are two numbers listed. One on a =
> sticker that reads 6160V ADT, the other is stamped on the plastic it =
reads=20
> M6924, whick one is the model # ?
> "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message=20
> news:Ynb6e.2$yB.104@xxxxxxxxxxxxxxxxxx
> Of what, the keypad?...you'd have to open it up..or describe it =
here...or go=20
> to Ademco's website and see if you can match it up with a pix there. =
The=20
> model number is not usually on the keypad..its usually inside on the =
board.=20
> ADT's numbers will be the same as Ademco's.
>=20
> The reciever model is on the reciever's board, open the can - the =
reciever=20
> is the circuit board above the main board the model number is part of =
the=20
> circuit board traces (top middle). If there is no reciever in the can, =
and=20
> you DO have wireless points on the system, you may have a keypad with =
RF=20
> reciever built into it.
>=20
> BTW... IF you are still monitored by ADT do NOT mess with it...you =
probably=20
> can't if you are still monitored anyway.
>=20
>=20
>=20
>=20
> "." <jpmk@xxxxxxxxxxxxx> wrote in message=20
> news:Yx36e.37119$UW6.35553@xxxxxxxxxxxxxxxxxxxxxxxxx
> > Where would you find the model number?
> >
> > "Crash Gordon=AE" <NONE@xxxxxxxx> wrote in message
> > news:YS06e.789$AV3.1393@xxxxxxxxxxxxxxxxxx
> > It's the same as Vista 20P (pretty much).
> >
> > You'll need a programming keypad 6139 etc.
> >
> > You need to know if you have any room left on the reciever...check =
the
> > receiver model #...is it a 5881L, 5881M, 5881H. Also, how many xtmrs =
are=20
> > on
> > it now..including any keyfobs, pirs, gbs, wireless smokes, etc.
> >
> > Then just go into programming, Installer Code + Code 00, then to %56 =
to=20
> > add
> > the xtmr.
> >
> >
> > "." <jpmk@xxxxxxxxxxxxx> wrote in message
> > news:K606e.36791$UW6.14989@xxxxxxxxxxxxxxxxxxxxxxxxx
> > > How does one add a wireless X-mitter. And where can I get the =
Installer
> > > manual for this system?
> > >
> > >
> >
> >
> >=20
>=20
>=20
>
alt.security.alarms Main Index |
alt.security.alarms Thread Index |
alt.security.alarms Home |
Archives Home