Re: FCI 7200 Fire Panel

[mleuck <m.leuck@xxxxxxxxx>]

On Feb 9, 11:45=A0pm, Frank Kurz <t...@xxxxxxxxxxxxx> wrote:
> On 09/02/2011 11:01 AM, James B wrote:
>
>
>
>
>
>
>
>
>
> > On Feb 9, 12:58 am, Frank Kurz<t...@xxxxxxxxxxxxx> =A0wrote:
> >> On 08/02/2011 7:53 PM, James B wrote:
>
> >>> Does anyone here now how to run autoconfig on this panel? =A0When I t=
ry
> >>> to run it I get an "access denied" message. =A0The 7200 program manua=
l
> >>> says to log in with the level 4 code to run the config program. =A0I
> >>> have done this, but once it starts the autoconfig about 2 seconds
> >>> later it comes up with access denied.
>
> >>> One thing I noticed is the user codes are only 2 digits and the manua=
l
> >>> says they should be 6, so I think its a 7200 Micro control but im not
> >>> sure. =A0I contacted a local FCI dealer "the original installer" and
> >>> they told me the panel is no longer made and they are not sure they
> >>> have a tech that knows how to program it still. =A0They did say they
> >>> would send one out and quoted me 10 hours @135 per hour. =A0I am only
> >>> trying to add 1 monitor module to the system. =A0The current system o=
nly
> >>> has 5 points on it now. =A0Needles to say the dealer isnt intrested i=
n
> >>> such a small task, or helping me out.
>
> >>> Can anyone tell me the correct procedure for running autoconifg?
>
> >>> James
>
> >> There are two possible scenarios here.
>
> >> 1. =A0You haven't entered the correct password (which is weird because=
 it
> >> should boot you out immediately), or
>
> >> 2. =A0You haven't followed the correct sequence to get into
> >> auto-configure. =A0Are you trying to enter programming from the SCU or=
 do
> >> you have a KDU/KDU-L?
>
> >> --
> >> Frank Kurzwww.firetechs.net-Hide quoted text -
>
> >> - Show quoted text -
>
> > Frank,
>
> > It has a KDU, =A0the only thing that is different is when I log in and
> > it asks for a password. =A0The book says it should say "Enter Password
> > 000000" =A0this one is saying "Enter Password 00". =A0I enter the level=
 4
> > password and it accepts it. =A0I have tried a few wrong passwords on
> > purpose and it rejects them immediately. =A0The panel is not in alarm
> > when I log in but it does have 1 trouble "Extra Point" this is the
> > point I am tryiing to add.
>
> > James
>
> Level four password is 440000. =A0The programming sequence is really
> specific and straight forward. =A0If you need the manual, I can send it t=
o
> you. =A0Unless the password has been changed by the "installing company"
> (which is not uncommon), you should be able to configure the system.
> Give me a call later in the morning. =A0I'll be in the office after 1100
> hours (Pacific). =A0The 800 number is at the bottom of every page on our
> website.
>
> --
> Frank Kurzwww.firetechs.net


Hey Frank, do you have any idea if the OP is even qualified to work on
a fire panel? I realize he has a program manual but other than that
you have no idea what his abilities are and it IS a fire panel...