Re: Paragon Plus

["Roger" <rumble@xxxxxxxxxxxxxxxxx>]

If you check the Pyronix website (www.pyronix.com) you can download Paragon
Plus USER manual. To get the INSTALLER manual you have to have login
priviliges. I don't believe these are given to home users. I can get you an
installer manual, although this will not be until Monday.

My tip would be to wait until you get the manual, then read-off and write
down the current settings before attempting to reset the panel totally. If
all else fails then you have a record of how the panel was originally setup.


"BIG NIGE" <no.way@xxxxxxxxxxxxxxxx> wrote in message
news:zVoqe.10274$m4.4308@xxxxxxxxxxxxxxxxxxxxxxx
> If you can post an e-Mail Address I will scan and send but it will not be
> tonight
>
> Be Careful not to post your exact e-mail address  alter it and give me
> instructions on how to correct it
>
> Default programming is
> ALL PROGRAMS
>
> Zone 1 = Entry/Exit  (starts entry timer)
>
> Zone 2  =Access ( switches off whilst entry timer is running to allow you
> to
> get to the keypad)
>
> Zones 3,4,5,6 are ALL Immediate
>
> Entry/Exit time is 30 Seconds
> Siren time is 20 minutes before re-set & re-arm.
>
> "Chris" <no@xxxxxxxxxx> wrote in message
> news:hLoqe.18381$%21.7362@xxxxxxxxxxxxxxxxxxxxxxx
>> "BIG NIGE" <no.way@xxxxxxxxxxxxxxxx> wrote in
>> news:VCoqe.10049$m4.9231@xxxxxxxxxxxxxxxxxxxx:
>>
>> > To Default ALL the Programming
>> > I will assume that you have located the main control unit and are not
>> > working from a remote keypad
>> >
>> > Remove mains power (assuming that the battery in the panel is ok then
>> > the outside siren should NOT sound)
>> >
>> > Loose small pozi screw at top of main control unit  (do not remove
>> > fully only unscrew enough to allow top of front to swing forward ) you
>> > may need to get your fingernails in as they can be a bit tight.  AS
>> > you swing it forward it will become unattatched at the bottom (BE
>> > CAREFUL THAT THE BATTERY DOES NOT FALL OUT AS YOU DO THIS) It should
>> > be held in place with a strap but they often are not.
>> >
>> > Disconnect the battery from the connectors  (at this point the
>> > External SIREN should sound)
>> >
>> > Hold in buttons 1 & 4 and re-connect battery &/OR mains you should now
>> > have default codes AND programming
>> >
>> >
>> > "BIG NIGE" <no.way@xxxxxxxxxxxxxxxx> wrote in message
>> > news:Xpoqe.19529$iy2.1468@xxxxxxxxxxxxxxxxxxxxxxx
>> >> I dont have a PDF of the manual  (which includes instructions on how
>> >> to default the programming
>> >>
>> >> I want to avoid defaulting the programming if possible atm so that we
>> >> can check on the programming already installed.
>> >>
>> >> To default the codes you have to default ALL programming.
>> >>
>> >> Has the Back page of your engineers manual been filled in with the
>> >> zones, how they are programmed and the timers etc
>> >>
>> >> "Chris" <no@xxxxxxxxxx> wrote in message
>> >> news:Lboqe.18263$%21.7897@xxxxxxxxxxxxxxxxxxxxxxx
>> >> > >> You say that you know the limited user code but not the master
>> >> > >> code or the engineers code
>> >> > >> I will assume that it is 5678 that you are using because the
>> >> > >> original installer dropped a clanger and didnt change it.
>> >> > >> as you are aware the original master code was 1234.
>> >> > >>
>> >> > >> As they didnt seem to know what they were doing we will check to
>> >> > >> see if
>> >> > > the
>> >> > >> original engineers code is still in rather than defaulting the
>> >> > >> whole
>> >> > > system
>> >> > >> straight off.
>> >> >
>> >> > The limted user code i have is not the default 5678.  I really
>> >> > think i need the installers manual and the method to default the
>> >> > system, If nto can you recommend anyone local to me who can come
>> >> > out and sort it for
>> > me?
>> >> >
>> >> > Preferably for the price of a few pints!! :-)
>> >>
>> >>
>> >
>> >
>>
>> Ok i'll give it a try but how do i then re-programme the different PIR's
>> to make the entry/exit zones, immediate activation etc.  Or what is the
>> default programme set to?
>>
>> If you could scan the manual or something i will give you an e-mail
>> address to send it to.
>>
>> Thanks again
>>
>> Chris
>
>