Re: GEMINI P3200 KEYPAD MESSAGE

[proguardsec@xxxxxxxxx]

=CE=A4=CE=B7 =CE=9A=CF=85=CF=81=CE=B9=CE=B1=CE=BA=CE=AE, 9 =CE=A3=CE=B5=CF=
=80=CF=84=CE=B5=CE=BC=CE=B2=CF=81=CE=AF=CE=BF=CF=85 2012 9:10:17 =CE=BC.=CE=
=BC. UTC+3, =CE=BF =CF=87=CF=81=CE=AE=CF=83=CF=84=CE=B7=CF=82 (=CE=AC=CE=B3=
=CE=BD=CF=89=CF=83=CF=84=CE=BF=CF=82) =CE=AD=CE=B3=CF=81=CE=B1=CF=88=CE=B5:
> =CE=A4=CE=B7 =CE=9A=CF=85=CF=81=CE=B9=CE=B1=CE=BA=CE=AE, 9 =CE=A3=CE=B5=
=CF=80=CF=84=CE=B5=CE=BC=CE=B2=CF=81=CE=AF=CE=BF=CF=85 2012 2:16:15 =CE=BC.=
=CE=BC. UTC+3, =CE=BF =CF=87=CF=81=CE=AE=CF=83=CF=84=CE=B7=CF=82 Frank Kurz=
 =CE=AD=CE=B3=CF=81=CE=B1=CF=88=CE=B5:
>=20
> > On 08/09/2012 10:07 PM, proguard wrote:
>=20
> >=20
>=20
> > > On 9 =CE=BF=CE=8F=C2=BD=CE=BF=CE=8F=C2=BD=CE=BF=CE=8F=C2=BD=CE=BF=CE=
=8F=C2=BD, 02:33, G. Morgan <sealte...@xxxxxxxxxxxxxxxxx> wrote:
>=20
> >=20
>=20
> > >> proguard...@xxxxxxxxx Wrote:
>=20
> >=20
>=20
> > >>
>=20
> >=20
>=20
> > >>> I get "enter your code to access area" at GEM-DXRP1 keypad connecti=
ng to a Gemini P3200. Even master security code want work. Any idea?
>=20
> >=20
>=20
> > >>> Thank you!
>=20
> >=20
>=20
> > >>
>=20
> >=20
>=20
> > >> If you are trying to get into programming, is it KP #1 ?  Programmin=
g
>=20
> >=20
>=20
> > >> has to be done on that one.
>=20
> >=20
>=20
> > >>
>=20
> >=20
>=20
> > >> Master code wont disarm IIRC if that's what you're trying to do.
>=20
> >=20
>=20
> > >>
>=20
> >=20
>=20
> > >> If the system was working and you just came to service, power-cycle =
it
>=20
> >=20
>=20
> > >> first - that fixes everything on those POS panels. <g>
>=20
> >=20
>=20
> > >>
>=20
> >=20
>=20
> > >> What *are* you trying to do?
>=20
> >=20
>=20
> > >
>=20
> >=20
>=20
> > > I made a cold start to the panel and after that i made doownload.
>=20
> >=20
>=20
> > > Everything was ok.
>=20
> >=20
>=20
> > > I was downloading the panel which was in disarm mode and after ending
>=20
> >=20
>=20
> > > download this message came up.
>=20
> >=20
>=20
> > > I took the panel on the bench in order to find out what happens.
>=20
> >=20
>=20
> > > The keypad is in address 01. Of course i power cycle it but after the
>=20
> >=20
>=20
> > > panel boot up this msg came up:
>=20
> >=20
>=20
> > > "Enter our code to access area" I used master security code, dealer
>=20
> >=20
>=20
> > > code, user code 1, user code 2, but still the same.
>=20
> >=20
>=20
> > > "Invalid access code, try again" It's the first time i saw this msg..=
.
>=20
> >=20
>=20
> > >
>=20
> >=20
>=20
> >=20
>=20
> >=20
>=20
> > I'm not all that familiar with the Napco products, but it sounds to me=
=20
>=20
> >=20
>=20
> > like you've programmed the keypad as a global partition and it's not=20
>=20
> >=20
>=20
> > actually "parked" in the one you want to arm.  Try entering partition 1=
=20
>=20
> >=20
>=20
> > from the keypad and then it should work normally.  When you download it=
=20
>=20
> >=20
>=20
> > again (as I'm sure you will), try assigning it to partition 1 and I=20
>=20
> >=20
>=20
> > think you'll avoid getting this message.
>=20
> >=20
>=20
> >=20
>=20
> >=20
>=20
> >=20
>=20
> >=20
>=20
> > --=20
>=20
> >=20
>=20
> > Fire Protection Technicians Network
>=20
> >=20
>=20
> > www.firetechs.net
>=20
>=20
>=20
> Its the most strange situation. The panel denies to answer the incoming c=
all for dl and always get the message "enter your code to access area" !!!
>=20
> i cannot get into programming even with master security code!

Also after start up the panel i get st the keypad "NAPCO I S #1 IN" and aft=
er that the msg "enter your code to access area"...=20
i am confused :-(