Re: your feedback on DIY security alarm system

[Jack Edin <nospam@logicunlimited.com>]

I believe most if not all current alarm panels can detect if the phone
line is cut.

The mighty M1 from Elk surely can, and does!

I use an M1 Gold myself. Spend the extra money - go for the gold!

Most alarm systems have the phone wired such that the home's incoming
PSTN wires loop through the alarm panel, THEN back out to the house. As
such if the phone is in use, the alarm can still take control and dial
out - as needed. This also prevents the intruder from interrupting the
call out by picking up a phone within the house, etc.

The alarm will monitor the PSTN... This is a low level feature.

On a higher level the M1 is an automation controller. You program it
with "Rules" with just about ANY desired result.

So for example you might write a rule like this one:

WHENEVER TelephoneTamper becomes Active
AND Alarm is NOT Armed
THEN Speak "Warning: Telephone is disabled"
THEN send e-mail message #2
Then...


The AND statement shown isn't needed, of course. But I show you to
illustrate the kind of control you have. M1 knows if it is Dark or Light
outside, and that might make a difference to you...

You can have multiple Rules for any given situation. So if the alarm was
armed, in Away-mode, and the PSTN goes away, you might choose to
activate the siren(s) and flash the lights, etc.

You can control the action(s) easily. The ElkRP software works very
well. Use it to program the M1 with your PC via serial, or even modem.

Add the Ethernet option to the Elk, and you can communicate with the M1
over your LAN or over the Internet! And the M1 can send e-mails, etc.

ElkRM software is a cool option, and I love it! I use it on a wireless
PDA to monitor and control the M1. It also allows M1 controlled things
like lights and thermostat to be controlled by my hand-held device
wirelessly.

I use MisterHouse software, and I've interfaced it with the Elk M1 too.
I have MH send messages to the M1 over the LAN, and I've written Rules
to deal with them. For example I use MH to do a CallerID lookup. Each
database entry has a category (vendor, family, friend, etc.) associated
with it. So if it is a friend, the word "Friend" - when received by the
M1 on it's ethernet port, will trigger it to speak a pre-defined
message! Same thing as when my mailbox is opened: A wireless signal
received my MH results in M1 telling the home's occupants verbally.

If you want it ALL, and you know the extra $$$ spent divided by the
number of years of service you'll get out of it (not to mention the
improved functionality) make it an easy choice...

You want the Elk M1 Gold.

Now go shopping!

;-)

Jack
:)



aerosmith wrote:
> Hi,
>
> One question about Elk M1EZ8 though. If any of the wired connections get
>  disconnected or if the PSTN wired is cut off from the control unit does
> the device set off an alarm in another way (like triggering the siren
> through the speakers)? If the PSTN wire is cut off how can the alarm
> system notify the owner? Can we run some software elsewhere on the
> internet and keep poking the control unit to see if it is reachable or
> something like that? I am just thinking about the extreme conditions
> where the burglar might cut off the PSTN or the magnetic sensor wires
> before breaking in.
>
> Thanks.
>
>
> On 8/8/2006 10:07 PM, IVB wrote:
>> add the Elk M1EZ8 to your list of panels to check out.  For a great
>> site to review the Elk, check out www.cocoontech.com
>>
>> I use the Elk M1 Gold. See my site below for the GUI software I use to
>> manage it.
>>