The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: xPL-Probe-Temp Sensing



Hi Guys

>After a frustrating two weeks and trying  bits of different codes  i
>have
>managed to get my probe system to read the temp sensor...At the moment
>though it  only has a tolerence of .5degree but hopefully down the
>track i
>can mod the code to get it down to 1/10 degree.....

Just found out why i had so much grief.......

My pic code is for a Dallas 1820 (now 18s20)  9 bit and the sensors i got
from Justin appear to be ds18b20 12 bit ....I already had 2 sensors and
these were both ds1820,s and these of coursed worked ok when polled
...........

Anyway  initially its only going to support 9 bit sensors and maybe later i
will add support for the ds18b20,s.....

Going to order some ds18s20,s to try as  some hvpro users have had problems
reading them..........

More Soon
Frank

----- Original Message -----
From: Frank Mc Alinden
To: ukha_xpl@xxxxxxx
Sent: Saturday, August 13, 2005 9:11 AM
Subject: [ukha_xpl] xPL-Probe-Temp Sensing


Hi All
Thought i would mention a little project i have been working on for
a few weeks now..
I  currently use the TOM10 board for temp sensing, but thought it would be
nice if my Probe system could also monitor temp sensors as well as video +
led probes....This would save me a cat5 cable in each room ..as i have a
probe zone box currently in each room

First thing i did was surf the net for some asm pic code for the dallas
1820
1 wire temp sensor.
After a frustrating two weeks and trying  bits of different codes  i have
managed to get my probe system to read the temp sensor...At the moment
though it  only has a tolerence of .5degree but hopefully down the track i
can mod the code to get it down to 1/10 degree.....

Some resistor changed was  required in the Probe zone box ( and also the
probe hub) , my intension is to make probes 5+6 of each zone box a temp
probe  OR standard probe input ..The probe hub will auto detect if a temp
sensor is present....

Next is to order some dallas 1820 sensors and mod my  probe system and  try
it out ...Still a bit of work to be done............

Tonys xPL-PROBE plugin might require a slight mod as can be seen by the
captured message below it reports the temp as status rather than
current.....

xpl-stat
{
hop=1
source=aec-probe.test
target=*
}
probe.basic
{
zone=test5
probe=probe5
status=20.5 c
}

More Soon
Frank

www.armaghelectrical.com.au



xPL Links: http://www.xplproject.org.uk http://www.xplhal.com http://www.xpl.myby.co.uk
To Post a Message: ukha_xpl@xxxxxxx
To Subscribe:  ukha_xpl-subscribe@xxxxxxx
To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx



SPONSORED LINKS Communication and networking  Home automation  Tcp ip
Tcp port  Extremely  Computer internet


------------------------------------------------------------------------------
YAHOO! GROUPS LINKS

a..  Visit your group "ukha_xpl" on the web.

b..  To unsubscribe from this group, send an email to:
ukha_xpl-unsubscribe@xxxxxxx

c..  Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


------------------------------------------------------------------------------



[Non-text portions of this message have been removed]




xPL Main Index | xPL Thread Index | xPL Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.