RE: Re: Geovision questions

["Paul Gale" <groups@xxxxxxxxxxxxxxxx>]

Yes - that's the one I have.

Why don't you send an email to Geovision support to see if there's another
=
way of doing it - They are very helpful.

-----Original Message-----
From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On Behalf Of G=
eraint Williams
Sent: 20 August 2005 20:29
To: ukha_d@xxxxxxx
Subject: [ukha_d] Re: Geovision questions

Is yours the same version as this Paul ?

http://www.rfconcepts.co.uk/GVDSP-8.pdf

as you can see, it uses a 40pin IDE cable to link between the cpature=20
card and the DSP, and i need the IDE connector on the capture card to=20
go to the daughterboard if i want to run more than 4 cameras.

Cheers
G


--- In ukha_d@xxxxxxx, "Paul Gale" <groups@s...> wrote:
> I have the DSP8 card - very good and I feed it into my video dist=20
system and send it round using a load of Kat5 modules.
>=20
> Not sure about the ribbon cable bit though.
>=20
> Paul.
>=20
> > -----Original Message-----
> > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On=20
Behalf Of
> > Geraint Williams
> > Sent: 20 August 2005 14:20
> > To: ukha_d@xxxxxxx
> > Subject: [ukha_d] Re: Geovision questions
> >=20
> > On this question of real time streaming, I was thinking that
maybe
> > the GV-DSP card would be suited, and then the outputs fed into a
> > modulator so that the cameras could be viewed realtime on=20
television
> > sets around the house rather than just PC's.
> >=20
> > If this is the case, then my problem would be that the GV650 I=20
have
> > has the 4 BNCs on board and then the rest need to be connected
to=20
the
> > daughterboard via the IDE cable, but if i use a GV-DSP, then
that=20
too
> > also uses the IDE connector and would appear i have two choices :
> >=20
> > 1) only use max 4 cameras plus GV-DSP card and can send modulated
> > output around tv system
> >=20
> > 2) use GV650 daughterboard and have upto 8 cameras, but no way of
> > linking in the GV-DSP card and therefore more restricted to pc's
> > being able to view.
> >=20
> >=20
> > I also have a nice Media Centre PC, and unsure best way to
have=20
that
> > access the cameras, preferably with control also.
> > The GV650 is not in this machine, and as i haven't used
remoteview
> > yet I'm not sure if this also has PTZ control available.
> > I really would of wanted as near to 25fps viewing from tv's or=20
local
> > LAN machines.
> >=20
> > I'm up in loft running cables as we speak to node0. Way too
hot=20
for
> > loft work ;)
> >=20
> > thoughts ?
> >=20
> > Cheers
> > Geraint.
> >=20
> >=20
> > --- In ukha_d@xxxxxxx, "Paul Gale" <groups@s...>
wrote:
> > > Not sure about the termination - they don't have any
physical
> > terminators.
> > >
> > > You can stream over the LAN in a number of ways. The first
is=20
using
> > the web viewer but this isn't in real time - but fairly quick.
The
> > second is to use the RemoteView LAN application. This is again=20
fairly
> > quick but I don't think it's 25fps - certainly not with several
> > cameras running. I think it all comes down to how many cameras
you
> > are monitoring at once and how many are being monitored by the=20
card
> > (for motion detection recording). The biggest factor is the
card=20
and
> > how many frames it's capable of dealing with.
> > >
> > > Paul.
> > >
> > > > -----Original Message-----
> > > > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx]=20
On
> > Behalf Of
> > > > Richard Malcolm-Smith
> > > > Sent: 20 August 2005 07:58
> > > > To: ukha_d@xxxxxxx
> > > > Subject: [ukha_d] Geovision questions
> > > >
> > > > Few Q's on this as the flakey webcam software on the
BT878=20
card
> > is getting
> > > > on my
> > > > nerves here.
> > > >
> > > > Do the cards have selectable termination so I can look
the=20
video
> > thru to
> > > > another
> > > > device as well? (I lifted the 75=CE=A9 resistor from my
BT878=20
card so
> > I could)
> > > > - I
> > > > want to feed the cams to a modulator too.
> > > >
> > > > Also, can I stream from the geovision machine over the
lan to
> > another
> > > > computer
> > > > at good quality in real time (real time as in no
perceviable
> > delay so
> > > > lipsync is
> > > > still ok when talking on the phone to the person at
the=20
camera)
> > > >
> > > > Also, the major issue I have with the current setup is
that I
> > have to take
> > > > snaps
> > > > at a really low resolution otherwise I get
interlacing=20
artifacts.
> > is there
> > > > either hardware or software deinterlace on the cards to
give
> > decent
> > > > quality?
> > > >
> > > >
> > > > [Non-text portions of this message have been removed]
> > > >
> > > >
> > > >
> > > > ------------------------ Yahoo! Groups Sponsor
---------------
----
> > -~-->
> > > > <font face=3Darial size=3D-1><a
> > > >
> >=20
href=3D"http://us.ard.yahoo.com/SIG=3D12hk0l7de/M=3D362343.6886680.7839639.=
2
> > 9202
> > > >
> >=20
18/D=3Dgroups/S=3D1705041992:TM/Y=3DYAHOO/EXP=3D1124528293/A=3D2894350/R=3D=
0/SIG=3D1
> > 0tj5
> > > > mr8v/*http://www.globalgiving.com";>Make
a difference. Find and
> > fund world-
> > > > changing projects at
GlobalGiving</a>.</font>
> > > >
--------------------------------------------------------------
----
> > --~->
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> > Yahoo! Groups Links
> >=20
> >=20
> >=20
> >=20
> >







=20