xAP 1.2 _will_ be released this week, honest. The current hold-up is that
i=
t's come to light that there's a bug in MS winsock on loopback
interfaces..=
. which is a real nightmare because it turns out that the hub protocol
brea=
ks.
Currently looking at whether we can come up with an alternative loopback
wi=
nsock shim, or whether the hub spec needs tweaking.
Arrggg!
Mark
-----Original Message-----
From: Chris Bond [mailto:chris@xxxxxxx]
Sent: 1 December 2002 13:37
To: ukha_d@xxxxxxx
Subject: RE: [ukha_d] Color kinetics
Dare I ask if we've got any more news when we can get your board into
production - im quite keen to get them built - with the latest xap spec
would be even better.
Kind Regards,
Chris Bond
-----Original Message-----
From: Ian Davidson [mailto:ian@xxxxxxx]
Sent: 06 November 2002 8:02 PM
To: ukha_d@xxxxxxx
Subject: Re: [ukha_d] Color kinetics
OK - The controller I built is still in its rat nests form but still
working
fine.
I started to look at adding some sort of RS232 control so that if it
came to
it a could produce one pcb to be used either as a standalone controller
or a
RS232 controller.
I also took another look at the xAP happenings. There is PIC code
available
by the other Ian's in the group for xAP on a PIC. However the PIC sits
there
constantly looking at the serial stream and when it receives the
correct
packet actions the request. I need to keep the DMX o/p going all the
time.
It is beyond a small PIC to o/p DMX and monitor and decode a RS232
stream.
Although I could increase the PIC to a more powerful unit it will still
mean
writing some fancy interupt routines. The easiest way is to use two
small
PIC's (only adds =A31.45 on to the cost) and let them talk at the
appropriate
time.
There seems to have been a change in the xAP protocol recently and also
mention of PIC code to handle xAP on its own. I was going to post to
the
xAP
group but they have seemed quite busy of late with the protocol changes
etc.
So for the time being the project is holding. I would be interested if
anyone has any ideas on this or if anyone form the xAP group would like
to
comment ?
Ian D
> Any news on the DMX controller ya built?
>
> -----Original Message-----
> From: Ian Davidson [mailto:ian@xxxxxxx]
> Sent: 06 November 2002 7:24 PM
> To: HA Yahoo group UK
> Subject: [ukha_d] Color kinetics
>
> Hi All
>
> I had been holding off posting hoping to have some more news by now.
I=
> spoke to the supplier again today, he asked me to phone again next
> Tuesday so I'll hold off until then to see if I can finally get
the
> remaining units.
>
> Ian D
>
>
>
> [Non-text portions of this message have been removed]
>
>
> http://www.automatedhome.co=
.uk
> Post message: ukha_d@xxxxxxx
> Subscribe: ukha_d-subscribe@xxxxxxx
> Unsubscribe: ukha_d-unsubscribe@xxxxxxx
> List owner: ukha_d-owner@xxxxxxx
>
> List of UKHA Groups here -
> http://grou=
ps.yahoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/in=
fo/terms/
>
>
>
> http://www.automatedhome.co=
.uk
> Post message: ukha_d@xxxxxxx
> Subscribe: ukha_d-subscribe@xxxxxxx
> Unsubscribe: ukha_d-unsubscribe@xxxxxxx
> List owner: ukha_d-owner@xxxxxxx
>
> List of UKHA Groups here - http://groups.ya=
hoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/te=
rms/
>
>
>
________________________________________________________________________
This email has been scanned for all viruses by the MessageLabs SkyScan
service. For more information on a proactive anti-virus service working
around the clock, around the globe, visit http://www.messagelabs.com
________________________________________________________________________
Comments to the Webmaster are always welcomed, please use
this contact form
. Note that as this site is a mailing list archive, the Webmaster has no control
over the contents of the messages. Comments about message content should be directed
to the relevant mailing list.