Re: GEM-RP1CAe2 replacement

[Jim <alarminex@xxxxxxx>]

On Feb 7, 11:16=A0am, wallstreet123456 <szigg...@xxxxxxxxx> wrote:
> On Feb 7, 8:13=A0am, wallstreet123456 <szigg...@xxxxxxxxx> wrote:
>
>
>
>
>
> > On Feb 7, 12:17=A0am, Jim <alarmi...@xxxxxxx> wrote:
>
> > > On Feb 6, 8:45=A0pm, wallstreet123456 <szigg...@xxxxxxxxx> wrote:
>
> > > > On Feb 6, 4:18=A0pm, Jim <alarmi...@xxxxxxx> wrote:
>
> > > > > On Feb 6, 3:57=A0pm, wallstreet123456 <szigg...@xxxxxxxxx> wrote:
>
> > > > > > I checked the keypad and it is not locked to the panel soI will=
 be
> > > > > > able to switch it out no problem. When I do the swap must I pow=
er down
> > > > > > the entire alarm (remove the batter and unplug the power pack f=
rom the
> > > > > > wall?)
>
> > > > > > Do I need to move the jumper also?
>
> > > > > > After I replace the keypad and power up the unit is there anyth=
ing
> > > > > > else I need to do or should it just (hopefully) work again.
>
> > > > > > Thanks to everyone in this form for being so helpful to me in t=
he
> > > > > > past.
>
> > > > > > Steven
>
> > > > > Did you go into the keypad configuration mode now to determine wh=
at
> > > > > the configuration of your present keypad is? You should do that f=
irst
> > > > > so that you know how to configure your new keypad. If your old ke=
ypad
> > > > > configuration was changed in any way during installation and you =
don't
> > > > > know what the changes are, you could wind up with some problems. =
Go
> > > > > from point to point in the configuration mode an write down the
> > > > > setting in each. ( see how to get into the configuration mode bel=
ow.
> > > > > Just don't power the system down now.)
>
> > > > > Once having determined what your present keypad configuration is,
> > > > > power down the entire system, ( transformer and battery) Change t=
he
> > > > > keypad. Move the jumper on the panel PCB. Power up the panel plug=
ing
> > > > > the transformer in first and quickly attaching the battery. The s=
ystem
> > > > > will come up in the "OUT OF SYSTEM" mode at the keypad. Press in =
11123
> > > > > and the function button to get into the keypad configuration mode=
 and
> > > > > make it the same as your present keypad. Look at the Installation=
/
> > > > > Programing insturctions for specifics on how to do this. Once thi=
s is
> > > > > completed, move the jumper on the panel PCB back to the run posit=
ion
> > > > > and run for cover. =A0Nah!
>
> > > > > It may take more than a minute for the keypad to return to the no=
rmal
> > > > > running mode.
>
> > > > Also, after I copy my settings down and put them into the keypad ho=
w
> > > > do I save them, must I hit reset on the pad or some other key when =
I
> > > > am finished entering my settings?-
>
> > > Pushing the On/Off key saves but I STRONGLY suggest that =A0you PLEAS=
E
> > > read the installation/programing instructions for doing this. I'm
> > > giving you information from my memory. I've been doing this for over
> > > 40 years. Much of what I do is so automatic that it's difficult for m=
e
> > > to know if I'm telling you all the necessary steps that need to be
> > > done. I do it by rote now. If I forget to tell you to do something
> > > and =A0you F.... k up, there's possibly not going to be an easy way t=
o
> > > get =A0you out of trouble. LOOK AT THE INSTRUCTIONS.
>
> > > And another suggestion: after you THINK you have everything right, go
> > > back and look at each programed configuration page, checking it
> > > against =A0your list before you leave the configuration mode.
> > > THEN ...... you push the reset key. Not before.- Hide quoted text -
>
> > > - Show quoted text -
>
> > Thanks for the tip. I do plan on looking at it but from looking at it
> > in the past it is a little confusing.- Hide quoted text -
>
> > - Show quoted text -
>
> I thought that all the information in the keypad was stored in the
> panel and when I swiched the keypad it would all flow into the new
> one. This was very helpful Jim.
>
> If I do something wrong when setting it up (Just want to make sure) if
> I put the old keypad back on will it work again?-

Yes,,,,,,,,,,,,,,