Re: DL900 Software

[make_at_3i_dot_co_dot_za@xxxxxxx (make)]

make had written this in response to
http://secure-gear.com/alt.security.alarms/5/Re-DL900-Software-article41174-.htm
 :
 Hi Rich, Thanks  for the help, this is the only panel I have, the access
code for the panel is the default 8480000 and I'm assuming I have to put
in my personal master code 4 digit that i have programmed into the panel,
- under "control panel" -  "user number 1" - "code'

Attempted to connect using all modems listed in Software, but only 69)
Creative Modemblaster Flash 56 gives a connection but eventually shows
?error wring to Module 0?.0? and hangs up.
I actually hear the modem hanging up the line about 5 seconds after the
panel has answered message comes on screen, thereafter another 60 odd
second before the message error... comes up. the line is already off
during this time.

my problem then is that the modem is hanging up too quickly, and i have to
find out how to stop it doing so with some commands or ....

Please HELP me setup this modem with commands. The panel is set to answer
at the 6th ring because the service provider has a call answer on 8th ring

Additional settings and a walk through of all settings appreciated. I am
in South Africa.

Thanks in advance,

Make make@xxxxxxxx


-------------------------------------
Rich wrote:

> Is this the only panel you have?
> Can you try it with another?
> Is the access code the same?

> Did some one pick up the phone at the alarm panel?



> "make" <make_at_3i_dot_co_dot_za@xxxxxxx> wrote in
> message
> news:47850f3b$0$3401$a82e2bb9@xxxxxxxxxxxxxxxxxxxxxxxx
>> make had written this in response to
>>
>>
http://secure-gear.com/alt.security.alarms/5/Re-DL900-Software-article40698-.htm
>> :
>> Hi Guys,
>>
>> I am a newbie here and appreciate some help with my problem with
>> NX8e
>> panel
>> I have just downloaded version 3.04 but can't connect via dial up
>> modem to
>> panel using all the advice here, panel answers and and I get
>> message
>> "error downloading to module0....0'
>>
>> I have tried changing baud rates
>>
>> My modem is a Agere Systems HDA modem in an Acer Laptop
>>
>> All help appreciated ...
>> Thanks
>> -------------------------------------
>> Rich wrote:
>>
>>> It worked before I changed the hard drive.
>>> I moved the data from my laptop over.
>>
>>
>>
>>> "brent" <bren@xxxxxxx> wrote in message
>>> news:ykkbj.47719$K27.33368@xxxxxxxxxxxxxxxxxxxxxxxxx
>>>>
>>>> "Rich" <Rich3784@xxxxxxxxxxx> wrote in
>>>> message
>>>> news:d9ydnUzdPaU4XfDanZ2dnUVZ_rOqnZ2d@xxxxxxxxxxxxxx
>>>>> What do you have for a # 66
>>>>> AOpen (Acer) 56K internal
>>>>>
>>>>> Q0E0V1S9=1
>>>>> S7=255S 10=255X0N1S37=3N0
>>>>>
>>>>> All 0 are numbers 0 not the letter
>>>>> I am using a Generic Fax Data Modem 56K
>>>>
>>>> this works for my 56K modem
>>>> S7=255S10=255X0T&Q0&K0S37=3N0&C1
>>>> with 1200 baud rate
>>>>
>>>> sure DL access code is correct?
>>>> good luck
>>>>
>>
>>
>>
>>
>>
>>
>>
>> ##-----------------------------------------------##
>> Delivered via http://www.secure-gear.com
>> The Internet Knowledge Base for the security industry
>> no-spam access to your favorite newsgroup -
>> alt.security.alarms - 37596 messages and counting!
>> ##-----------------------------------------------##







##-----------------------------------------------##
Delivered via http://www.secure-gear.com
The Internet Knowledge Base for the security industry
no-spam access to your favorite newsgroup -
alt.security.alarms - 37771 messages and counting!
##-----------------------------------------------##