Re: Ademco:PanelDumpsCentralStation

["Crash Gordon" <webmaster@xxxxxxxxxxxxxxxxxxxxx>]

ah like the old stuff



"Jim Rojas" <jrojas@xxxxxxxxxxxx> wrote in message
news:w8U%e.8944$UD6.2244@xxxxxxxxxxx
| With the Vista50P, you have to do it manually.
|
| Location 32 is the Account number (enter 15 15 15 15)
| Location 35 is the call back number
| Location 36 is the CSID (enter 15 15 15 15 15 15 15 15)
| Location 37 enables download (enter 11011111) last 2 digits enable upload
&
| download
| Location 153 to disable call back (enter 0)
|
| When you call the panel select first time communication with default
account
| number, no call back. This way you are guaranteed to get into the panel.
| Once you are connected to the panel, upload all data, make your changes,
| then download to panel. Compass will automatically insert the proper
account
| number.
|
| I suggest you select Ademco Contact ID as the format. Also on the bottom
of
| the screen, Compass can insert all the default Contact ID codes
| automatically. This is handy and will save you some time. You still
however
| must enable signals like Low Battery, Tests, Cancel, Exit Error, etc...its
| all on one screen.
|
| Jim Rojas
|
| "Crash Gordon" <webmaster@xxxxxxxxxxxxxxxxxxxxx> wrote in message
| news:qmT%e.4$nm5.527@xxxxxxxxxxxxxxxxxx
| > Mark says it doesn't do that on a 50P. I don't use 50Ps.
| >
| >
| > "James" <trishnjames@xxxxxxxxxxx> wrote in message
| > news:8KadnYIef_OE86LenZ2dnUVZ_sydnZ2d@xxxxxxxxxxxxxx
| > | *96 wipes the account number and resets the CSID code for a first time
| > | communication.
| > |
| > | James
| > |
| > | "Crash Gordon" <webmaster@xxxxxxxxxxxxxxxxxxxxx> wrote in message
| > | news:XlI%e.134$Mx2.11093@xxxxxxxxxxxxxxxxxx
| > | > Forget the *96 I was thinking of smaller panels.
| > | >
| > | > If you're doing commercial fire I suggest you get a qualified
| > installer
| > to
| > | > finish your job - or you may never pass inspection.
| > | >
| > | >
| > | > "Don" <dgp0@xxxxxxxxxxxxx> wrote in message
| > | > news:1128219617.693817.322540@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
| > | > | Mssrs. Gordon and Rojas,
| > | > |
| > | > | I do not know my transmission format.  I believe it to be the
| > default.
| > | > | I believe the default is Ademco low speed.
| > | > |
| > | > | I do not know the central station's receiver kind.
| > | > |
| > | > | Each smoke is on its own zone.  I have not definitively worked out
| > the
| > | > | amperage but I have another 12-volt, 7-amp ready to wire to the
| > panel
| > | > | in parallel with the first, if that is the correct thing to do.
| > | > |
| > | > | Security system is part of an ongoing building renovation project.
| > | > | Project has new insurer.  Insurer demands site be telephone
| > monitored
| > | > | or they will drop me.  The problem has persisted for three months!
| > | > | They are tired of waiting for compliance.
| > | > |
| > | > | I will get back to the site on 03Oct05.  I will
| > | > | 01 go to Section 1*53  and enter 0.  If that does not work, I will
| > do
| > | > | as you both recommend and
| > | > |
| > | > | 02 wipe the account number.
| > | > |
| > | > | 03 For "First time communication" I will re-program the same
account
| > | > | number, primary and secondary telephone numbers with the same
| > numbers
| > | > | (?!) I just wipe.  Then I will call the central station and ask
them
| > to
| > | > | try again.
| > | > |
| > | > | What is *96?
| > | > |
| > | > | Thanks for the guidance.  I hope it works.  I will let you know,
| > either
| > | > | way.
| > | > |
| > | > | Thanks again.
| > | > |
| > | > | Don
| > | > |
| > | >
| > | >
| > |
| > |
| >
| >
|
|