The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: Re: xPLRioNet v3.8z released


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: Re: HV Macro runs multiple times




Hi George

> Yes, I get multiple messages in the xPL monitor. It usually shows 3
> instances - yet the macro executes up to 6 times.

If its receiving multiple copies of the same command each time a button is
pressed , a delay may be required to filter out  some of the repeated
commands....I think Mal would need to have a look at this.....

I assume you have tried very short presses and still get multiple received
w800 messages ??

Frank

----- Original Message -----
From: "gmotichka" <gmotichka@xxxxxxx>
To: <ukha_xpl@xxxxxxx>
Sent: Sunday, December 05, 2004 6:25 AM
Subject: [ukha_xpl] Re: HV Macro runs multiple times


>
>
> Yes, I get multiple messages in the xPL monitor. It usually shows 3
> instances - yet the macro executes up to 6 times.
>
> George
>
>
>
>
>
> --- In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
<fmcalind@b...>
> wrote:
> > > I am getting very close on this working. I now have it where
the
> x10
> > > signal is recognized by the W800 and then triggers the macro
in
> > > HomeVision.
> >
> > Good news.......
> >
> > > The problem is that it will execute the macro multiple times
--
> > > anywhere from 3 to 6 times consecutively. I can see the
multiple
> > > commands going to HV. I tried to add a 'macro disable"
command in
> > > the macro, but that did not help. Neither did adjusting the
> ddespeed
> > > or lastsent options in the configuration
> >
> > Are you receiving multiple message in xPL Monitor ?? when you
> press a button
> > on your rf remote ???......If so The w800-app might require a
> built in delay
> > ....Hopefully Mal will post regarding the app.......
> >
> > Frank
> >
> >
> > ----- Original Message -----
> > From: "gmotichka" <gmotichka@h...>
> > To: <ukha_xpl@xxxxxxx>
> > Sent: Sunday, December 05, 2004 5:20 AM
> > Subject: [ukha_xpl] HV Macro runs multiple times
> >
> >
> > >
> > >
> > > I am getting very close on this working. I now have it where
the
> x10
> > > signal is recognized by the W800 and then triggers the macro
in
> > > HomeVision.
> > >
> > > The problem is that it will execute the macro multiple times
--
> > > anywhere from 3 to 6 times consecutively. I can see the
multiple
> > > commands going to HV. I tried to add a 'macro disable"
command in
> > > the macro, but that did not help. Neither did adjusting the
> ddespeed
> > > or lastsent options in the configuration.
> > >
> > > Further suggestions would be welcomed.
> > >
> > > Thanks
> > > George
> > >
> > >
> > >
> > >
> > >
> > >
> > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > http://www.xpl.myby.co.uk
> > > To Post a Message: ukha_xpl@xxxxxxx
> > > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> > >
>
>
>
>
>
>
> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
http://www.xpl.myby.co.uk
> To Post a Message: ukha_xpl@xxxxxxx
> To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> Yahoo! Groups Links
>
>
>
>
>
>
>




xPL Main Index | xPL Thread Index | xPL Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.