Re: HV Macro runs multiple times

["gmotichka" <gmotichka@xxxxxxxxxxxxx>]

Nope. Just one address. Even did an ipconfig /all to verify

George



-- In ukha_xpl@xxxxxxx, Tom Van den Panhuyzen <tomvdp@g...>
wrote:
> Ah...  Could it be you have multiple IP-addresses on that pc ?
>
>
>
> On Sat, 04 Dec 2004 19:25:54 -0000, gmotichka <gmotichka@h...>
wrote:
> >
> > Yes, I get multiple messages in the xPL monitor. It usually
shows 3
> > instances - yet the macro executes up to 6 times.
> >
> > George
> >
> >
> >
> >
> >
> > --- In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
<fmcalind@b...>
> >
> >
> > wrote:
> > > > I am getting very close on this working. I now have it
where
the
> > x10
> > > > signal is recognized by the W800 and then triggers the
macro
in
> > > > HomeVision.
> > >
> > > Good news.......
> > >
> > > > The problem is that it will execute the macro multiple
times --
> > > > anywhere from 3 to 6 times consecutively. I can see the
multiple
> > > > commands going to HV. I tried to add a 'macro
disable"
command in
> > > > the macro, but that did not help. Neither did adjusting
the
> > ddespeed
> > > > or lastsent options in the configuration
> > >
> > > Are you receiving multiple message in xPL Monitor ?? when
you
> > press a button
> > > on your rf remote ???......If so The w800-app might require
a
> > built in delay
> > > ....Hopefully Mal will post regarding the app.......
> > >
> > > Frank
> > >
> > >
> > > ----- Original Message -----
> > > From: "gmotichka" <gmotichka@h...>
> > > To: <ukha_xpl@xxxxxxx>
> > > Sent: Sunday, December 05, 2004 5:20 AM
> > > Subject: [ukha_xpl] HV Macro runs multiple times
> > >
> > >
> > > >
> > > >
> > > > I am getting very close on this working. I now have it
where
the
> > x10
> > > > signal is recognized by the W800 and then triggers the
macro
in
> > > > HomeVision.
> > > >
> > > > The problem is that it will execute the macro multiple
times --
> > > > anywhere from 3 to 6 times consecutively. I can see the
multiple
> > > > commands going to HV. I tried to add a 'macro
disable"
command in
> > > > the macro, but that did not help. Neither did adjusting
the
> > ddespeed
> > > > or lastsent options in the configuration.
> > > >
> > > > Further suggestions would be welcomed.
> > > >
> > > > Thanks
> > > > George
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > > http://www.xpl.myby.co.uk
> > > > To Post a Message: ukha_xpl@xxxxxxx
> > > > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > > > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> >
> >
> >
> >
> >
> >
> >
> > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > http://www.xpl.myby.co.uk
> > To Post a Message: ukha_xpl@xxxxxxx
> > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> >
> >
> >
> > Yahoo! Groups Sponsor
> >
> > ADVERTISEMENT
> >
> >
> > ________________________________
> > Yahoo! Groups Links
> >
> > To visit your group on the web, go to:
> > http://groups.yahoo.com/group/ukha_xpl/
> >
> > To unsubscribe from this group, send an email to:
> > ukha_xpl-unsubscribe@xxxxxxx
> >
> > Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.