Re: Cutting PVC trunking cleanly...

[Phillip Harris <phil@xxxxxxxxxxx>]

LOL - You reckon? Might leave a few melted edges methinks... ;-)

Phil

On 14 Dec 2010, at 22:37, Mike Griffiths wrote:

> I was watching an old episode of Star Trek Voyager Phil
> And I think they had something that could sort you out Phil
>
> From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On Behalf Of Phil
Harris
> Sent: 12 December 2010 23:28
> To: ukha_d@xxxxxxx
> Subject: Re: [ukha_d] Cutting PVC trunking cleanly...
>
>
>
> I decided to take a shot at it today with my existing manual mitre saw
and I have to say it looks a bloody mess. :-)
>
> Obviously my old mitre saw has enough slop in it to completely arse up
even a basic 45 degree join so I may have to redo it (I have enough
trunking left I think)...
>
> Phil
>
> Sent from another bloody fruit-based portable device...
>
> On 12 Dec 2010, at 17:33, Stephen McGarry <stephen@xxxxxxx<mailto:stephen%40roselea.co.uk>>
wrote:
>
>> A thought is to make a piece of wood to fit inside the trunking
and support the sides while its being sawn with a mitre
>> saw. The Evolution saws have a fine blade which cuts less harshly
than standard saws (and they cut nearly everything).
>>
>> HTH
>> Stephen
>>
>> On 12/12/10 09:13, Peter + Jane wrote:
>>> I have a high end German sliding mitre saw and am
>>> near the end of a complicated self build. I have
>>> used the saw endlessly for plastic soil pipe and
>>> waste pipe. The trouble with trunking is it is a
>>> bit thin and flappy. You would need a very fine
>>> blade and would need to cut very slowly to avoid
>>> snatching, chipping or splintering. Hence my
>>> preference to mark with a pencil, cut with an
>>> angle grinder and then finesse back to the line.
>>> Simples!
>>> But each to their own!
>>> With a lot to do, an abrasive disc in a chop saw might be
ideal.
>>> Rgds
>>> Peter
>>> At 08:57 12/12/2010, you wrote:
>>>>
>>>>
>>>> PVC trunking ..... tricksy stuff....
>>>>
>>>> I think something like this
>>>> <http://www.screwfix.com/prods/33776/Power-Tools/Compound-Mitre-Saws/Erbauer-ERB238MSW-254mm-Sliding-Mitre-Saw-230V>http://www.screwfix.com/prods/33776/Power-Tools/Compound-Mitre-Saws/Erbauer-ERB238MSW-254mm-Sliding-Mitre-Saw-230V
>>>>
>>>> I have an Erbauer, cant recommend it enough. Given that
trunking is tricksy,
>>>> you might need something to trim the bits off
>>>> with so what about a Dremel 8000
>>>> as well.... just in case. :-) :-) :-)
>>>>
>>>> robin
>>>>
>>>> On 11/12/10 22:14, Phil Harris wrote:
>>>>> Wondering if I can use it as an excuse to get
>>>> a nice sliding compound mitre saw for myself
>>>> 'for Xmas' (but I might buy it tomorrow from Screwfix of
course...
>>>>>
>>>>> Phil
>>>>>
>>>>> Sent from another bloody fruit-based portable
device...
>>>>>
>>>>> On 11 Dec 2010, at 21:11, "Tracey
>>>> Gardner"<<mailto:tracey.gardner%40talktalk.net>tracey.gardner@xxxxxxx<mailto:tracey.gardner%40talktalk.net>
<mailto:tracey.gardner%40talktalk.net>>
>>>> wrote:
>>>>>
>>>>>> A chop saw with a decent high TPI blade would do
the trick.
>>>>>> Especially if you cut it with the lid on?
>>>>>>
>>>>>> Tracey
>>>>>>
>>>>>>> I need to cleanly cut mitres in some 4" x
2" rectangular profile trunking
>>>>>>> and was wondering if anyone knows whether it's
possible to use hot wire
>>>>>>> cutters to get a nice clean and square cut
>>>> or am I stuck with using my old
>>>>>>> 18TPI mitre saw which doesn't do that good a
job on the relatively floppy
>>>>>>> box section of the trunking...
>>>>>>>
>>>>>>> Phil
>>>>>>>
>>>>>>
>>>>>>
>>>>>> ------------------------------------
>>>>>>
>>>>>>
>>>>>> Yahoo! Groups Links
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>> ------------------------------------
>>>>>
>>>>>
>>>>> Yahoo! Groups Links
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>> [Non-text portions of this message have been removed]
>>>
>>>
>>
>>
>> ------------------------------------
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>
>
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please visit http://www.messagelabs.com/email
> ______________________________________________________________________
>
> ________________________________
> Antena Cyf
> Unit 2
> Cibyn
> Caernarfon
> LL55 2BD
>
> Tel: +44 (0)1286 662200
> Fax: +44 (0)1286 678594
>
> Antena Cyf. Rhif Cofrestredig 03626688
> Antena Cyf. Registered No. 03626688
>
> Email Disclaimer and Confidentiality Notice
> Ymwadiad Ebost a Rhybudd Cyfrinachedd
> http://www.antena.co.uk/email_disclaimer.htm
>
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please visit http://www.messagelabs.com/email
> ______________________________________________________________________
>
> [Non-text portions of this message have been removed]
>
>
>
> ------------------------------------
>
>
> Yahoo! Groups Links
>
>
>


------------------------------------

<*> Join the Automated Home Forums
http://www.automatedhome.co.uk/vbulletin/