RE: Silent Gliss Autoglide

[Rob James <rob68james@xxxxxxxxxxx>]

Sorry all, this was supposed to be off list.

=20

Rob
=20
> To: ukha_d@xxxxxxx
> From: rob68james@xxxxxxx
> Date: Sun, 19 Apr 2009 06:55:36 +0000
> Subject: RE: [ukha_d] Silent Gliss Autoglide
>=20
>=20
> Ben,
>=20
>=20
>=20
> Do you have any recommendations for the cable used for a 24v run back
to =
Comfort, also, for a 24v supply fed by a relay module, do you require an
ad=
ditional 24v supply, and if so, again any recommendations.
>=20
>=20
>=20
> Thanks in advance
>=20
>=20
>=20
> Rob
>=20
>=20
>=20
> To: ukha_d@xxxxxxx
> From: ben@xxxxxxx
> Date: Fri, 13 Mar 2009 08:18:00 +0000
> Subject: RE: [ukha_d] Silent Gliss Autoglide
>=20
>=20
>=20
>=20
>=20
> Andrew,
>=20
> You would need to connect the curtain supply to a fused spur. I would
alw=
ays
> supply the spur from the ring main, but if you can only get to the
lighti=
ng
> circuit then it will be fine for the odd curtain.=20
>=20
> If your doing the whole house I would put all the curtains on there
only
> circuit, or run each one back to node 0 and install a 24v supply.
>=20
> Ben
>=20
> _____=20
>=20
> From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On Behalf Of
> Andrew Walker
> Sent: 12 March 2009 07:51
> To: ukha_d@xxxxxxx
> Subject: RE: [ukha_d] Silent Gliss Autoglide
>=20
> Ok, thanks for that.
>=20
> So the motor electronics must be permanently wired/plugged into the
> mains? Would a fused spur be required? Could it come off the lighting
> circuit?
>=20
> -----Original Message-----
> From: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> [mailto:ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com] On Beh=
alf
> Of Neil Fuller
> Sent: 11 March 2009 20:24
> To: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> Subject: Re: [ukha_d] Silent Gliss Autoglide
>=20
> Andrew
>=20
> The 5090 just needs a momentary closure of the switch to initiate an
> "open" or "close".
>=20
> As Ben said, you remove the switch and connect it to a CBUS relay (the
> CBUS relays are volt free).
>=20
> Set cbus up so that the relay closes for a short period via a Timer
> action(1 second is more than enough) to initiate an "open"
or "close" of
> the curtains. Set the Timer delay up in the Blocks tab
>=20
> Currently, mine operate from one of the buttons on the Saturn switches
> but will operate via light level when I get around to it!
>=20
> HTH
>=20
> Neil
>=20
> Andrew Walker wrote:
> >
> > Hi Ben,
> >
> > I am thinking of adding some curtain control in the near future,
could
>=20
> > you explain how it is achieved with a simple cbus relay. I
thought I=20
> > would need one of the new cbus blind and shutter control relays?
> >
> > cheers
> >
> > -----Original Message-----
> > From: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>=20
> > [mailto:ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>]
On=20
> > Behalf Of ben addison
> > Sent: 10 March 2009 22:48
> > To: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>
> > Subject: RE: [ukha_d] Silent Gliss Autoglide
> >
> > Hi Rob,
> >
> > The RACUB should be fine to control the 5090, I use the 5090 on
most=20
> > jobs and control them from a c-bus relay or comfort.
> >
> > The RACUB looks to be a zero volt relay.
> >
> > All you need to do is just cut the switch off that comes with the
5090
>=20
> > then connect the green and yellow wire across the N/O relay.
> >
> > I do sell Silent Gliss products if you would like me to quote
for=20
> > anything.
> > Most items can be delivered to you the same week.
> >
> > Thanks
> >
> > Ben Addison
> >
> > _____
> >
> > From: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>=20
> > [mailto:ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>]
On=20
> > Behalf Of Rob James
> > Sent: 10 March 2009 22:25
> > To: ukha_d@yahoogroups. <mailto:ukha_d%40yahoogroups.com>
com
> <mailto:ukha_d%40yahoogroups.com>
> > Subject: [ukha_d] Silent Gliss Autoglide
> >
> > I've been looking at the Silent Gliss Autoglide 5090 system but I
have
>=20
> > a few questions that hopefully someone can answer.
> >
> > I have Rako controlled lighting in use in the room I would like
to use
>=20
> > these curtains motors, but I'm not sure whether the 5090 basic
model=20
> > will be compatible with the RACUB.
> >
> > If it is compatible, and if I wasn't worried about independant
curtain
>=20
> > control, could more than one 5090 be used with a single RACUB?
> >
> > Can anyone recommend a competitive supplier?
> >
> > Regards
> >
> > Rob
> >
> > __________________________________________________________
> > Free photo editing software from Windows Live . Try it now!
> > http://clk.atdmt.
<http://clk.atdmt.
> <http://clk.atdmt.com/UKM/go/134665240/direct/01/>
> com/UKM/go/134665240/direct/01/
> > <http://clk.atdmt. <http://clk.atdmt.com/UKM/go/134665240/direct/01/>
> com/UKM/go/134665240/direct/01/>>
> > com/UKM/go/134665240/direct/01/
> >
> > [Non-text portions of this message have been removed]
> >
> > Internal Virus Database is out of date.
> > Checked by AVG - www.avg.com
> > Version: 8.0.233 / Virus Database: 270.10.18/1935 - Release Date:
> > 02/04/09 16:35:00
> >
> > [Non-text portions of this message have been removed]
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >=20
>=20
> ------------------------------------
>=20
> Yahoo! Groups Links
>=20
> Internal Virus Database is out of date.
> Checked by AVG - www.avg.com
> Version: 8.0.233 / Virus Database: 270.10.18/1935 - Release Date:
02/04/0=
9
> 16:35:00
>=20
> [Non-text portions of this message have been removed]
>=20
>=20
>=20
>=20
>=20
>=20
>=20
>=20
>=20
> _________________________________________________________________
> Share your photos with Windows Live Photos =96 Free.
> http://clk.atdmt.com/UKM/go/134665338/direct/01/
>=20
> [Non-text portions of this message have been removed]
>=20
>=20
>=20
> ------------------------------------
>=20
> Yahoo! Groups Links
>=20
>=20
>=20

_________________________________________________________________
View your Twitter and Flickr updates from one place =96 Learn more!
http://clk.atdmt.com/UKM/go/137984870/direct/01/

[Non-text portions of this message have been removed]



------------------------------------