Re: Fw: IR Control of multiple xboxes all in one location - Node 0

["noel_pilot" <HA@xxxxxxxxxxxxxxxxxx>]

Ok, thanks for the info, My last hope is that i don't actually need to
be able to use all of the available buttons on the xbox remote, well
in fact i need to get it to the point of only needing 50% of them.
Then change the keymaps on one to use the 50% of buttons not used by
the other xbox, so all the codes will go to both xboxes just half will
be ignored by each xbox.

web devices are of course an option but for sheer simplicity my
harmony remote just works!

Will post back how i get on in the new year.

Cheers

Noel

--- In ukha_d@xxxxxxx, Gareth Cook <g@...> wrote:
>
> Well, you could start buggering about with relays - using them to
route
> the physical wire - could be messy
>
> Cant see you doing what you want - theres only one set of IR. Even
with my
> Popcorn we cant do that. Which is why I have one over a HDMI matrix.
>
>  Gareth Cook MBCS CITP
>  Technical Solution Architect, SWG Sales Europe
>
>
>
> ----- Forwarded by Gareth Cook/UK/IBM on 16/12/2008 19:27 -----
>
> Discussion
> Main Topic
>
> ukha_d@xxxxxxx
> Today 18:29
>
> .
> Subject:
> .
> Re: Fw: [ukha_d] IR Control of multiple xboxes all in one location -
Node
> 0
> .
> Category:
>
>
>
> Thanks Gareth, but what about if I wanted to control both.
>
> Scenario is I'll have two xboxes both in Node 0, one primarily for the
> lounge, one for the bedroom.  Normally zoned control would be fine.
>
> However....at times I'll be watching a film downstairs, want to pause
> it, go upstairs and press play to continue watching upstairs.  Hence
> the need to control both xboxes but ideally with different sets of IR
> codes??!
>
> Cheers
>
> Noel
>
>
> --- In ukha_d@xxxxxxx, Gareth Cook <g@...> wrote:
> >
> > http://www.letsautomate.com/10719.cfm
> >
> > Multi-zone IR - cheaper in the US of course :-)
> >
> >
> >
> >
> > Hi all,
> >
> > I know a few of you have got multiple xboxes with xbmc in your
setups.
> >  If you have them co-located in Node 0 or similar how do you
ensure
> > you control the one you mean to with your IR remote?  The only
thought
> > I've had so far is to have completely different keymap.xml setups
for
> > each one but I'm not sure if that's doable or if I'm limited by a
> > certain number of IR commands it'll recognise.
> >
> > Can anyone advise??
> >
> > Thanks
> >
> > Noel
> >
> >
> > ------------------------------------
> >
> > ********************************************
> > Limited Time Offer - Free iPhone VAT Calculator
> > http://berble.com/index.php/component/content/article/109
> > ********************************************
> >
> >
> >
> >
> >
> >
> >
> >
> > Unless stated otherwise above:
> > IBM United Kingdom Limited - Registered in England and Wales with
> number
> > 741598.
> > Registered office: PO Box 41, North Harbour, Portsmouth,
Hampshire
> PO6 3AU
> >
> >
> >
> >
> >
> >
> >
> > [Non-text portions of this message have been removed]
> >
>
>
>
> ------------------------------------
>
> ********************************************
> Limited Time Offer - Free iPhone VAT Calculator
> http://berble.com/index.php/component/content/article/109
> ********************************************
>
>
>
>
>
>
>
>
> Unless stated otherwise above:
> IBM United Kingdom Limited - Registered in England and Wales with
number
> 741598.
> Registered office: PO Box 41, North Harbour, Portsmouth, Hampshire
PO6 3AU
>
>
>
>
>
>
>
> [Non-text portions of this message have been removed]
>



------------------------------------

********************************************
Limited Time Offer - Free iPhone VAT Calculator
http://berble.com/index.php/component/content/article/109
********************************************