The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Lets Automate CM12U X10 HA controller - software I/F options.


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: Projector Screen Control


  • Subject: Re: Projector Screen Control
  • From: "Chris Purves" <CHRIS_PURVES@xxxxxxx>
  • Date: Tue, 13 Dec 2005 13:35:45 -0000

Although I did not program mine, I understand start and stop points
are all part of the programming (pls check).

Direct from Marata as I understand it.

C



--- In ukha_d@xxxxxxx, "Brian Milton" <bmilton@b...> wrote:
>
> I was thinking of doing that.  Can the down IR command be programed to
> run fora time period?  So i can get the screen exactly where i want
> it. Save me opening the screen to adjust the lower position and
> voiding my waranty.
>=20
> Where did you get it? Can i just buy it directly from Marata?
>=20
> Thanks
> Brian
>=20
> --- In ukha_d@xxxxxxx, "Chris Purves"
<CHRIS_PURVES@M...> wrote:
> >
> > I programmed the 'down' ir command on the unit to the on button
of my
> > sony projector remote and the 'up' to the off button. Worked
> > flawlessly. Costs about =A3300 though but it will defo do the
job.
> >=20
> >=20
> > Chris
> > --- In ukha_d@xxxxxxx, "Brian Milton"
<bmilton@b...> wrote:
> > >
> > > Thanks Chris,
> > >=20
> > > Looks like a good piece of kit.  This will do the job, and
might
link
> > > it up with the curtains as well. :)
> > >=20
> > > Cheers
> > >=20
> > > Brian
> > >=20
> > > --- In ukha_d@xxxxxxx, "christopher purves"
> > > <CHRIS_PURVES@M...> wrote:
> > > >
> > > > Hi,
> > > >=20
> > > > This is a fantastic little unit.
> > > >=20
> > > > http://www.marata.co.uk/Downloads/mcu300-4spec-sheet.pdf
> > > >=20
> > > > It has IR in and only needs power and will happily sit
in your
> > ceiling.
> > > >=20
> > > > Programmerd from pc it will happily control your screen
and
respond
> > > to IR.
> > > >=20
> > > >=20
> > > > Chris
> > > >=20
> > > >=20
> > > > >From: "Brian Milton" <bmilton@b...>
> > > > >Reply-To: ukha_d@xxxxxxx
> > > > >To: ukha_d@xxxxxxx
> > > > >Subject: [ukha_d] Projector Screen Control
> > > > >Date: Tue, 13 Dec 2005 09:54:24 -0000
> > > > >
> > > > >Hi guys,
> > > > >
> > > > >Looking to control my Projector screen.  I ran a
2.5 T&E to my
> screen
> > > > >when i was wiring thinking i can contol my screen
from my
> Node0.  But
> > > > >the screen has a four core cable! oops!  So now all
i can do is
> > supply
> > > > >the screen with power throught the T&E.  I was
wondering if
> there is
> > > > >any sort of IR controlled relay or somehting that i
could put
> in the
> > > > >ceiling beside the screen and control it with my
remote.  Would
> like
> > > > >to have a flush plate on the ceiling with just the
IR seen.=20
> Would an
> > > > >X10 type device be the way to go?
> > > > >
> > > > >Also i would like to be able to set a timer? so
that the screen
> stops
> > > > >where i want it not all the way to the end.  Or is
there a way to
> > > > >change where the motor stops as it goes down a
little to far?
Oh i
> > > > >have a Cat5e cable running to node0 and one
directly to my
> projector
> > > > >if they would help in any ideas.
> > > > >
> > > > >Any pointers?
> > > > >
> > > > >Thanks
> > > > >Brian
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > >
> >
>







UKHA_D Main Index | UKHA_D Thread Index | UKHA_D Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.