Re: Projector Screen Control

["Brian Milton" <bmilton@xxxxxxxxxxx>]

I was thinking of doing that.  Can the down IR command be programed to
run fora time period?  So i can get the screen exactly where i want
it. Save me opening the screen to adjust the lower position and
voiding my waranty.

Where did you get it? Can i just buy it directly from Marata?

Thanks
Brian

--- In ukha_d@xxxxxxx, "Chris Purves" <CHRIS_PURVES@M...>
wrote:
>
> I programmed the 'down' ir command on the unit to the on button of my
> sony projector remote and the 'up' to the off button. Worked
> flawlessly. Costs about =A3300 though but it will defo do the job.
>=20
>=20
> Chris
> --- In ukha_d@xxxxxxx, "Brian Milton" <bmilton@b...>
wrote:
> >
> > Thanks Chris,
> >=20
> > Looks like a good piece of kit.  This will do the job, and might
link
> > it up with the curtains as well. :)
> >=20
> > Cheers
> >=20
> > Brian
> >=20
> > --- In ukha_d@xxxxxxx, "christopher purves"
> > <CHRIS_PURVES@M...> wrote:
> > >
> > > Hi,
> > >=20
> > > This is a fantastic little unit.
> > >=20
> > > http://www.marata.co.uk/Downloads/mcu300-4spec-sheet.pdf
> > >=20
> > > It has IR in and only needs power and will happily sit in
your
> ceiling.
> > >=20
> > > Programmerd from pc it will happily control your screen and
respond
> > to IR.
> > >=20
> > >=20
> > > Chris
> > >=20
> > >=20
> > > >From: "Brian Milton" <bmilton@b...>
> > > >Reply-To: ukha_d@xxxxxxx
> > > >To: ukha_d@xxxxxxx
> > > >Subject: [ukha_d] Projector Screen Control
> > > >Date: Tue, 13 Dec 2005 09:54:24 -0000
> > > >
> > > >Hi guys,
> > > >
> > > >Looking to control my Projector screen.  I ran a 2.5
T&E to my
screen
> > > >when i was wiring thinking i can contol my screen from
my
Node0.  But
> > > >the screen has a four core cable! oops!  So now all i
can do is
> supply
> > > >the screen with power throught the T&E.  I was
wondering if
there is
> > > >any sort of IR controlled relay or somehting that i
could put
in the
> > > >ceiling beside the screen and control it with my remote.
 Would
like
> > > >to have a flush plate on the ceiling with just the IR
seen.=20
Would an
> > > >X10 type device be the way to go?
> > > >
> > > >Also i would like to be able to set a timer? so that the
screen
stops
> > > >where i want it not all the way to the end.  Or is there
a way to
> > > >change where the motor stops as it goes down a little to
far?  Oh i
> > > >have a Cat5e cable running to node0 and one directly to
my
projector
> > > >if they would help in any ideas.
> > > >
> > > >Any pointers?
> > > >
> > > >Thanks
> > > >Brian
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> >
>