RE: IRM +FirM Interfacing Update

["Nikola Kasic" <nikola@xxxxxxx>]

Hi Frank,
Just checked my single gang box.
Dimensions are 68x68x25mm
So probably it will fit into double gang one.
Can you tell me what's the depth of the device?

There's no way for me to bring CAT5 close enough to use stick on
emitters.

What are feedback problems?

Cheers,
Nik
  -----Original Message-----
  From: Frank Mc Alinden [mailto:armagh@xxxxxxx]
  Sent: 24 October 2002 12:19
  To: ukha_d@xxxxxxx
  Subject: Re: [ukha_d] IRM +FirM Interfacing Update


  Hi Nik
             
I think there would be problems if using ir blaster type
  emitting......i have only tested the system with stick on
emitters........Im
  sure there would be feedback problems...Have you located your cat5
points
  above were your equipment is....if so is there any way you can get a
thin
  type speaker wire down to the equipment to use for emitters????
  > And if it is, will it fit into a single gang box?
  Its been a long time since i seen a UK plate.....the pcb is around
75mm x
  50mm

  Frank
  ----- Original Message -----
  From: "Nikola Kasic" <nikola@xxxxxxx>
  To: <ukha_d@xxxxxxx>
  Sent: Thursday, October 24, 2002 8:13 PM
  Subject: RE: [ukha_d] IRM +FirM Interfacing Update


  > Hoooray!
  > Three times...
  > But, of course, nothing is perfect, so to get SWMBO approval i
would
like
  to
  > put transmitters and receivers high on the wall in a box behind
a
blanking
  > plate. I would then drill a hole in a plate for IR LEDs.
  > Is something like that possible?
  > And if it is, will it fit into a single gang box?
  > And will single CAT5 cable be enough for both Tx and Rx?
  > Electrician put the cables throug the strategic points last
week, and
he's
  > not finished yet. I left enough length curled and hidden for
the future
IR
  > solution, but if I can do it the way I plan, I might order
  > transmitters/receivers and ask electrician to put boxes in
place and
  cables
  > through wall to each box.
  >
  > Dan's idea of controling lights via IR is interesting.
  > But where transmitters must be placed relative to IR receiver
on light
  > switch? Can they be on the same wall? That means that IR signal
will
have
  to
  > bounce off the walls. Is that possible and will they bounce off
any wall
  and
  > furniture, or just some (e.g. wall carpets).
  >
  > Cheers
  > Nik
  >   -----Original Message-----
  >   From: Frank Mc Alinden [mailto:armagh@xxxxxxx]
  >   Sent: 22 October 2002 20:40
  >   To: ukha_d@xxxxxxx
  >   Subject: Re: [ukha_d] IRM +FirM Interfacing
Update
  >
  >
  >   Thats correct Nik
 
>                              
Hopefully when finished (the pc interface)
  a
  > pc
  >   user can have a multizone rx tx /rx using
Automat8it software with
Dans
  >   plugins and my pc interface + FirM .
  >
  >   Frank
  >   ----- Original Message -----
  >   From: "Nikola Kasic"
<nikola@xxxxxxx>
  >   To: <ukha_d@xxxxxxx>
  >   Sent: Wednesday, October 23, 2002 1:35 AM
  >   Subject: RE: [ukha_d] IRM +FirM Interfacing
Update
  >
  >
  >   > Frank, if I understand properly, with IRM and
FirM you can use PC
  >   (Autom8it)
  >   > as a brain and control where the commands will
be transmitted. That
  way
  > IR
  >   > commands will not be sent through the whole
house, but to the
  >   pre-programed
  >   > zones only. Also, we don't need a HV for
controling FirM, but can
use
  > PC.
  >   > Can you tell me am I right?
  >   > Cheers,
  >   > Nik
  >   >   -----Original Message-----
  >   >   From: Frank Mc Alinden
[mailto:armagh@xxxxxxx]
  >   >   Sent: 22 October 2002 12:38
  >   >   To: ukha_d@xxxxxxx
  >   >   Subject: [ukha_d] IRM +FirM
Interfacing Update
  >   >
  >   >
  >   >   HI all
  >  
>           Just a
quick update on were Dan and I are at with Dans IRM
  and
  >   my
  >   > FirM....
  >   >
  >   >   Well at the moment Using Dans
software the pc can send a tx zone
  > command
  >   > to the FirM Interface and select a tx zone on
firm.......Also when
an
  ir
  >   > signal is received by Dans software it asks
the interface for zone
id
  > and
  >   > displays it on the pc........At this point im
trying to get my ir
  sytem
  >   > (firm + hv) to respond to a txed ir signal
with little luck not sure
  if
  >   its
  >   > a hardware problem????
  >   >
  >   >   More Soon
  >   >
  >   >   Frank
  >   >
  >   >   [Non-text portions of this message
have been removed]
  >   >
  >   >
  >  
>         Yahoo! Groups
Sponsor
  >  
>              
ADVERTISEMENT
  >   >
  >   >
  >   >
  >   >
  >   >
  >   >   http://www.automatedhome.co.uk
  >   >   Post message: ukha_d@xxxxxxx
  >   >   Subscribe: 
ukha_d-subscribe@xxxxxxx
  >   >   Unsubscribe: 
ukha_d-unsubscribe@xxxxxxx
  >   >   List owner: 
ukha_d-owner@xxxxxxx
  >   >
  >   >   List of UKHA Groups here -
  >   http://groups.yahoo.com/group/UKHA_Grouplists/
  >   >
  >   >   Your use of Yahoo! Groups is
subject to the Yahoo! Terms of
Service.
  >   >
  >   >
  >   >
  >   > [Non-text portions of this message have been
removed]
  >   >
  >   >
  >   >
  >   > http://www.automatedhome.co.uk
  >   > Post message: ukha_d@xxxxxxx
  >   > Subscribe:  ukha_d-subscribe@xxxxxxx
  >   > Unsubscribe: 
ukha_d-unsubscribe@xxxxxxx
  >   > List owner:  ukha_d-owner@xxxxxxx
  >   >
  >   > List of UKHA Groups here -
  > http://groups.yahoo.com/group/UKHA_Grouplists/
  >   >
  >   > Your use of Yahoo! Groups is subject to
  > http://docs.yahoo.com/info/terms/
  >   >
  >   >
  >
  >
  >         Yahoo! Groups
Sponsor
 
>              
ADVERTISEMENT
  >
  >
  >
  >
  >
  >   http://www.automatedhome.co.uk
  >   Post message: ukha_d@xxxxxxx
  >   Subscribe:  ukha_d-subscribe@xxxxxxx
  >   Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
  >   List owner:  ukha_d-owner@xxxxxxx
  >
  >   List of UKHA Groups here -
  http://groups.yahoo.com/group/UKHA_Grouplists/
  >
  >   Your use of Yahoo! Groups is subject to the Yahoo!
Terms of Service.
  >
  >
  >
  > [Non-text portions of this message have been removed]
  >
  >
  >
  > http://www.automatedhome.co.uk
  > Post message: ukha_d@xxxxxxx
  > Subscribe:  ukha_d-subscribe@xxxxxxx
  > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
  > List owner:  ukha_d-owner@xxxxxxx
  >
  > List of UKHA Groups here -
http://groups.yahoo.com/group/UKHA_Grouplists/
  >
  > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
  >
  >


        Yahoo! Groups Sponsor
             
ADVERTISEMENT





  http://www.automatedhome.co.uk
  Post message: ukha_d@xxxxxxx
  Subscribe:  ukha_d-subscribe@xxxxxxx
  Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
  List owner:  ukha_d-owner@xxxxxxx
  List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/

  Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.



[Non-text portions of this message have been removed]

Yahoo! Groups Sponsor

ADVERTISEMENT

http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx 
Subscribe:  ukha_d-subscribe@xxxxxxx 
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx 
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.