RE: Electronics help with IR TX-RX

["James Hoye" <james.hoye@xxxxxxx>]

This email was delivered to you by The Free Internet,
a Business Online Group company. http://www.thefreeinternet.net
---------------------------------------------------------------
The TSOPs work at 5v and as such need some sort of regulation - either
using
a 39p voltage regulator from M***** or the combination of a 5.1v Zener
diode
and a resistor.  Ian B's PCBs utilise the Zener/resistor - I'm sure he can
provide you with the circuit details.

I have a couple of spare TSOPs, and I'm sure Keith has quite a few left.

James H

> -----Original Message-----
> From: Graham Howe [mailto:graham@xxxxxxx]
> Sent: Tuesday, May 15, 2001 7:20 PM
> To: UKHA List (E-mail)
> Subject: [ukha_d] Electronics help with IR TX-RX
>
>
> As many of you know, I eventually managed to put together some working
IR
> transmitters and receivers with help from several on the list and
> despite my
> non-existent electronics knowledge. However I now have a problem, the
kit
> works fine when I use a 12V battery and connect both TX and RX to it
(with
> an additional wire between them for the signal). I am currently in the
> process of installing Comfort and so drilled a little hole in one of
the
> PIRs and inserted an IR RX unit. I connected the 12V and 0V from
> the PIR to
> the unit and used a spare wire in the CAT5 cable for the signal. Then
I
> connected up the TX unit via Krone blocks and patch panel and it
didn't
> work. After I finished cursing myself for not testing the set up
before
> gluing the RX inside the PIR I started to investigate. After much
probing
> with a voltmeter, I discovered that the 12V output from Comfort
> was actually
> 13.8V and that when fed with this voltage the kit wouldn't work,
> in fact the
> TS1308 (is that the right code? If not it is the things Keith was
selling)
> seemed to die after a while at this voltage (I now have 2 dead
> ones). I then
> tried having just the RX unit fed by Comfort and the TX fed by
> the battery,
> this didn't work either, even though I could see the 0.5V drop in the
> trigger wire when IR was received. At this point I started thinking
that I
> was well and truly out of my depth, so I started guessing what might
be
> wrong. Here are my thoughts:
>
> The RX unit will operate correctly for at least a limited time when
> connected to the 13.8V, the trigger wire shows 5V which drops to 4.5V
when
> IR is received.
>
> The TX unit does not appear to like the higher voltage at all and
> certainly
> doesn't react correctly to the trigger when the higher voltage is
applied
> (could it be that the 0.5V drop is no longer sufficient to do the
'magic'.
>
> Both a RX and a TX unit appear to have been killed during my
experiments,
> possibly as a result of the high voltage.
>
> It seems I have two options, either use an alternative power
> supply that is
> closer to 12V and therefore put up with less convenient wiring inside
my
> PIRs. Or use some sort of electronic trickery (possibly a resistor?)
to
> reduce the voltage supplied from Comfort (after all the Comfort
> outputs are
> labeled 12V).
>
> Please can one of you electronic geniuses give me some advice,
> with the DDAR
> price increase this is turning out to be a very unsuccessful day!
>
> Graham
>
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>




Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/