The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: xpl xbox suggestions


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: xPL...1 Wire


  • Subject: Re: xPL...1 Wire
  • From: Ian Lowe
  • Date: Sun, 25 May 2003 11:35:00 +0000

Thanks Stuart.

That, I suppose, firms up that a 1-wire bridge should ideally support
ibuttons, ds1820s, and 1-wire switch devices.

I guess the best way forward is to get a basic temperature setup going,
then
expand it from there.

Ian.

----- Original Message -----
From: "Stuart" <<a
href="/group/ukha_xpl/post?postID=KP0a68NvpKkqsJsjrmmMG9NQT1G0_RL802fNkTpyyPsz16IJRLhnbUfIoHPMR0ZED6h043eF5Q">swp@w...</a>>
To: <<a
href="/group/ukha_xpl/post?postID=-sBAKe3l2g9HUajbAct1ozIYq9fdopPCPMAubXxUE3nOxdRVBIdvoaiyrTZ7BfBylcwrqXML_q6n9effcVYNf3K4">ukha_xpl@xxxxxxx</a>>
Sent: Sunday, May 25, 2003 11:25 AM
Subject: Re: [ukha_xpl] xPL...1 Wire


> Hi Ian et al
>
> > Item four might be stretching a PIC a little too far, in which
case, one
> > for temperature, one for switches and so on. we can have multiple
PIC
> > devices on a 1-wire bus, as far a I am aware, so that should be
easy
> > enough to do..
>
> As I recall, the PIC will be a 1-wire master, the 1-wire spec clearly
> states that only one 1-wire master can exist on the 1-wire bus at any
> one time.
>
> Regards
>
> Stuart
>
>
>
>
> xPL Links: <a href="http://www.xplproject.org.uk";>http://www.xplproject.org.uk</a>
<a href="http://www.xplhal.com";>http://www.xplhal.com</a>
<a href="http://www.xpl.myby.co.uk";>http://www.xpl.myby.co.uk</a>
> To Post a Message: <a
href="/group/ukha_xpl/post?postID=-sBAKe3l2g9HUajbAct1ozIYq9fdopPCPMAubXxUE3nOxdRVBIdvoaiyrTZ7BfBylcwrqXML_q6n9effcVYNf3K4">ukha_xpl@xxxxxxx</a>
> To Subscribe: <a
href="/group/ukha_xpl/post?postID=w8XokltijP7idkNdUsVt0V7YTZw9aAy4ljlKwWt8GaKRJKmPXi99POeQggetZE6d6uVwVjfLxMe651_YarvMezkV5JSqhxzFhywyWNc">ukha_xpl-subscribe@xxxxxxx</a>
> To Unsubscribe: <a
href="/group/ukha_xpl/post?postID=LNyRVlsDvLpV9WJK3puiJJMch-iocNV47w_RDfZ1OrUJr_k4DIFQuT45lYErRkL20D_9tRQkfKiwlNJOQGsxSlBLDWSnUjWEHVc">ukha_xpl-unsubscribe@xxxxxxx</a>
>
> Your use of Yahoo! Groups is subject to <a href="http://docs.yahoo.com/info/terms/";>http://docs.yahoo.com/info/terms/</a>
>
>






xPL Main Index | xPL Thread Index | xPL Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.