The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: HouseBot Plug-in


  • Subject: Re: HouseBot Plug-in
  • From: "zagknut" <brad@xxxxxxxxxx>
  • Date: Fri, 25 Sep 2009 12:26:17 -0000

--1-3257327816-4985630396=:1
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable


These were indeed not checked, so I checked and ran my task, but no-go.
(I ran Pause) As I was rooting around, trying to figure out what else I
had done wrong, the Boom went into play. So, doing a little
invsestigating, I determined that it was taking 20 seconds for the task
to execute. I have attached a screen shot that shows the device call,
with the time last executed, which is 8:12:17. I also have the xFx
Message viewer running and you can see that the command didn't actually
execute until 8:12:47. Right-clicking on the task  after it executes
will show Runt Task Now grayed out and Stop Task Now as active. If I
execute Pause directly from the device by selecting the target, then hit
enter, it will send immediately. Any ideas?

Task Screen Shot
<http://groups.yahoo.com/group/xap_automation/photos/album/940785096/pic\
/1693434099/view?picmode=3Doriginal&mode=3Dtn&order=3Dordinal&start=3D1&dir=
=3Dasc>

Thanks!


--- In xap_automation@xxxxxxx, "Edward Pearson"
<edward.mailgroup@...> wrote:
>
> Thanks for the screenshots - it's the only really clear way of
communicating
> a HouseBot setup. One of it's few -ve points.
>
>
>
> One thing I can't see in the shots though is the detailed settings for
the
> 'xAP Message Target'. And it occurs to me that the behaviour you
depict is
> exactly what would happen if the checkbox 'Allow Same Value Settings'
for
> this property was unchecked. Can you check the setting of that please.
>
>
>
> From: xap_automation@xxxxxxx
[mailto:xap_automation@xxxxxxx]
> On Behalf Of zagknut
> Sent: 24 September 2009 20:00
> To: xap_automation@xxxxxxx
> Subject: [xap_automation] Re: HouseBot Plug-in
>
>
>
>
>
> I have attached a screenshot of the device for the first task in my
last
> e-mail.
>
> Device
>
<http://groups.yahoo.com/group/xap_automation/photos/album/940785096/pic\
/825
>
06861/view?picmode=3Dlarge&mode=3Dtn&order=3Dordinal&start=3D1&dir=3Dasc>=
screen
shot
>
>
> Regards, Brad
>
>
> --- In xap_automation@xxxxxxx, "Edward Pearson"
> edward.mailgroup@ wrote:
> >
> > writing a value, even if it's the same as the existing value,
from a
task
> > action into the target property of the sender device is the right
way to
> > trigger the message send.
> >
> >
> >
> > So you should have
> >
> > 1) a HB button that calls a task,
> >
> > 2) the task makes changes to a sender device, the last one being
the
> > target property
> >
> > 3) the sender device transmits the xAP message to SqueezeCenter
> >
> >
> >
> > Not sure I follow your description below. A screen shot of the
task
might
> > help.
> >
> >
> >
> > From: xap_automation@xxxxxxx
> [mailto:xap_automation@xxxxxxx]
> > On Behalf Of zagknut
> > Sent: 23 September 2009 23:02
> > To: xap_automation@xxxxxxx
> > Subject: [xap_automation] HouseBot Plug-in
> >
> >
> >
> >
> >
> > So, I made it past the hurdle of communicating with the
Squeezeboxes, now
> I
> > am stumped on the HouseBot Plug-in. Let me know if there is a
better
forum
> > for these questions.
> >
> > I have created a Sender device in HouseBot that will send the
button
> > commands to the correct squeezebox when I click on the
"Click to
test and
> > send message". So, I try to create a "macro" using
Tasks, but no
luck;
> > nothing is sent. In the help section of HouseBot on xAP Sender
Devices it
> > says "Writing a value to the xAP Message Target property
triggers
the xAP
> > message", so I use "add Action" item and chage my
button name
(favorites,
> > play, etc) and then the name of the target. Unfortunately, the
target name
> > is not changed between the "marco" calls and the
command is not
sent. So,
> I
> > try changing the target field to "-", which creates an
error message
in
> xFx
> > Viewer, but no problem. This works. Great I think, until I
realize
BOTH
> > Squeezeboxes are changing! I have the same problem with all
commands,
> other
> > than power and level. Any guidance on where I'm going astray
would
be MOST
> > appreciated. Again, I am looking to simulate button pushes on the
unit,
> such
> > as next track, pause, play, and a macro (favorites, down, play).
> >
> > Thanks in advance for any help you may be able to offer.
> > Brad
> >
>



--1-3257327816-4985630396=:1
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: 7bit





<head>

<style type="text/css">
<!--

/* start of attachment style */
.ygrp-photo-title{
clear: both;
font-size: smaller;
height: 15px;
overflow: hidden;
text-align: center;
width: 75px;
}
div.ygrp-photo{
background-position: center;
background-repeat: no-repeat;
background-color: white;
border: 1px solid black;
height: 62px;
width: 62px;
}

div.photo-title
a,
div.photo-title a:active,
div.photo-title a:hover,
div.photo-title a:visited {
text-decoration: none;
}

div.attach-table div.attach-row {
clear: both;
}

div.attach-table div.attach-row div {
float: left;
/* margin: 2px;*/
}

p {
clear: both;
padding: 15px 0 3px 0;
overflow: hidden;
}

div.ygrp-file {
width: 30px;
valign: middle;
}
div.attach-table div.attach-row div div a {
text-decoration: none;
}

div.attach-table div.attach-row div div span {
font-weight: normal;
}

div.ygrp-file-title {
font-weight: bold;
}
/* end of attachment style */
-->
</style>
</head>
<html><head>
<style type="text/css">
<!--
#ygrp-mkp{
border: 1px solid #d8d8d8;
font-family: Arial;
margin: 14px 0px;
padding: 0px 14px;
}
#ygrp-mkp hr{
border: 1px solid #d8d8d8;
}
#ygrp-mkp #hd{
color: #628c2a;
font-size: 85%;
font-weight: bold;
line-height: 122%;
margin: 10px 0px;
}
#ygrp-mkp #ads{
margin-bottom: 10px;
}
#ygrp-mkp .ad{
padding: 0 0;
}
#ygrp-mkp .ad a{
color: #0000ff;
text-decoration: none;
}
-->
</style>
</head>
<body>



<!-- **begin egp html banner** -->

<br><br>

<!-- **end egp html banner** -->


<P>These were indeed not checked, so I checked and ran my task, but
no-go. (I ran Pause) As I was rooting around, trying to figure out what
else I had done wrong, the Boom went into play. So, doing a little
invsestigating, I determined that it was taking 20 seconds for the task to
execute. I have attached a screen shot that shows the device call, with the
time last executed, which is 8:12:17. I also have the xFx Message viewer
running and you can see that the command didn't actually execute until
8:12:47. Right-clicking on the task&nbsp; after it executes will show
Runt Task Now grayed out and Stop Task Now as active. If I execute Pause
directly from the device by selecting the target, then hit enter, it will
send immediately. Any ideas?</P>
<P><A href="http://groups.yahoo.com/group/xap_automation/photos/album/940785096/pic/1693434099/view?picmode=original&amp;mode=tn&amp;order=ordinal&amp;start=1&amp;dir=asc";>Task
Screen Shot</A>&nbsp;</P>
<P>Thanks!</P>
<P><BR>--- In xap_automation@xxxxxxx, "Edward
Pearson" &lt;edward.mailgroup@...&gt;
wrote:<BR>&gt;<BR>&gt; Thanks for the screenshots -
it's the only really clear way of communicating<BR>&gt; a
HouseBot setup. One of it's few -ve points.<BR>&gt;
<BR>&gt; <BR>&gt; <BR>&gt; One thing I can't
see in the shots though is the detailed settings for the<BR>&gt;
'xAP Message Target'. And it occurs to me that the behaviour you depict
is<BR>&gt; exactly what would happen if the checkbox 'Allow Same
Value Settings' for<BR>&gt; this property was unchecked. Can you
check the setting of that please.<BR>&gt; <BR>&gt;
<BR>&gt; <BR>&gt; From: xap_automation@xxxxxxx [mailto:xap_automation@xxxxxxx]<BR>&gt;
On Behalf Of zagknut<BR>&gt; Sent: 24 September 2009
20:00<BR>&gt;
To: xap_automation@xxxxxxx<BR>&gt; Subject: [xap_automation] Re:
HouseBot Plug-in<BR>&gt; <BR>&gt; <BR>&gt;
<BR>&gt; <BR>&gt; <BR>&gt; I have attached a
screenshot of the device for the first tas
k in my last<BR>&gt; e-mail.<BR>&gt; <BR>&gt;
Device<BR>&gt; &lt;http://groups.yahoo.com/group/xap_automation/photos/album/940785096/pic/825<BR>&gt;
06861/view?picmode=large&amp;mode=tn&amp;order=ordinal&amp;start=1&amp;dir=asc&gt;
screen shot<BR>&gt; <BR>&gt; <BR>&gt;
Regards, Brad<BR>&gt; <BR>&gt; <BR>&gt; ---
In xap_automation@xxxxxxx, "Edward Pearson"<BR>&gt;
edward.mailgroup@ wrote:<BR>&gt; &gt;<BR>&gt;
&gt; writing a value, even if it's the same as the existing value, from
a task<BR>&gt; &gt; action into the target property of the
sender device is the right way to<BR>&gt; &gt; trigger the
message send.<BR>&gt; &gt; <BR>&gt; &gt;
<BR>&gt; &gt; <BR&
gt;&gt; &gt; So you should have<BR>&gt; &gt;
<BR>&gt; &gt; 1) a HB button that calls a
task,<BR>&gt; &gt; <BR>&gt; &gt; 2) the task
makes changes to a sender device, the last one being the<BR>&gt;
&gt; target property<BR>&gt; &gt; <BR>&gt;
&gt; 3) the sender device transmits the xAP message to
SqueezeCenter<BR>&gt; &gt; <
BR>&gt; &gt; <BR>&gt; &gt; <BR>&gt;
&gt; Not sure I follow your description below. A screen shot of the
task might<BR>&gt; &gt; help.<BR>&gt; &gt;
<BR>&gt; &gt; <BR>&gt; &gt; <BR>&gt;
&gt; From: xap_automation@xxxxxxx<BR>&gt; [mailto:xap_automation@xxxxxxx]<BR>&gt;
&gt; On Behalf Of zagknut<BR>&gt; &gt; Sent: 23 September
2009 23:02<BR>&gt; &gt; To:
xap_automation@xxxxxxx<BR>&gt; &gt; Subject: [xap_automation]
HouseBot Plug-in<BR>&gt; &gt; <BR>&gt; &gt;
<BR>&gt; &gt; <BR>&gt; &gt; <BR>&gt;
&gt; <BR>&gt; &gt; So, I made it past the hurdle of
communicating with the Squeezeboxes, now<BR>&gt;
I<BR>&gt; &gt; am stumped on the HouseBot Plug-in. Let me
know if there is a better
forum<BR>&gt; &gt; for these questions. <BR>&gt;
&gt; <BR>&gt; &gt; I have created a Sender device in
HouseBot that will send the button<BR>&gt; &gt; commands to
the correct squeezebox when I click on the "Click to test
and<BR>&gt; &gt; send message". So, I try to create a
"macro" usi
ng Tasks, but no luck;<BR>&gt; &gt; nothing is sent. In the
help section of HouseBot on xAP Sender Devices it<BR>&gt;
&gt; says "Writing a value to the xAP Message Target property
triggers the xAP<BR>&gt; &gt; message", so I use
"add Action" item and chage my button name
(favorites,<BR>&gt; &gt; play, etc) and then the name of the
target. Unfortunately, the target name<BR>&gt; &gt; is not
changed between the "marco" calls and the command is not sent.
So,<BR>&gt; I<BR>&gt; &gt; try changing the target
field to "-", which creates an error message in<BR>&gt;
xFx<BR>&gt; &gt; Viewer, but no problem. This works. Great I
think, until I realize BOTH<BR>&gt; &gt; Squeezeboxes are
changing! I have the same problem with all commands,<BR>&gt;
other<BR>&gt; &gt; than power and level. Any guidance on
where I'm going astray woul
d be MOST<BR>&gt; &gt; appreciated. Again, I am looking to
simulate button pushes on the unit,<BR>&gt;
such<BR>&gt; &gt; as next track, pause, play, and a macro (f
avorites, down, play).<BR>&gt; &gt; <BR>&gt;
&gt; Thanks in advance for any help you may be able to
offer.<BR>&gt; &gt; Brad<BR>&gt;
&gt;<BR>&gt;<BR></P>




<!-- **begin egp html banner** -->

<br>



<br>

<!-- **end egp html banner** -->


<div width="1" style="color: white; clear:
both;"/>__._,_.___</div>

<!-- Start Recommendations -->
<!-- End Recommendations -->



<!-- **begin egp html banner** -->

<img src="http://geo.yahoo.com/serv?s=97476590/grpId=9674343/grpspId=1705007709/msgId=4505/stime=1253881587";
width="1" height="1"> <br>

<!-- **end egp html banner** -->


<!-- **begin egp html banner** -->

<br>
<div style="font-family: verdana; font-size: 77%; border-top: 1px
solid #666; padding: 5px 0;" >
Your email settings: Individual EmailTraditional <br>
<a href="http://groups.yahoo.com/group/xap_automation/join;_ylc=X3oDMTJmM3VnNHFkBF9TAzk3NDc2NTkwBGdycElkAzk2NzQzNDMEZ3Jwc3BJZAMxNzA1MDA3NzA5BHNlYwNmdHIEc2xrA3N0bmdzBHN0aW1lAzEyNTM4ODE1ODc-";>Change
settings via the Web</a> (Yahoo! ID required) <br>
Change settings via email: <a href="mailto:xap_automation-digest@xxxxxxx?subject=Email
Delivery: Digest">Switch delivery to Daily Digest</a>  <a
href = "mailto:xap_automation-fullfeatured@xxxxxxx?subject=Change
Delivery Format: Fully Featured">Switch to Fully Featured</a>
<br>
<a href="http://groups.yahoo.com/group/xap_automation;_ylc=X3oDMTJkbXR0cDk0BF9TAzk3NDc2NTkwBGdycElkAzk2NzQzNDMEZ3Jwc3BJZAMxNzA1MDA3NzA5BHNlYwNmdHIEc2xrA2hwZgRzdGltZQMxMjUzODgxNTg3";>
Visit Your Group
</a>
<a href="http://docs.yahoo.com/info/terms/";>
Yahoo! Groups Terms of Use
</a>
<a href="mailto:xap_automation-unsubscribe@xxxxxxx?subject=Unsubscribe";>
Unsubscribe
</a>
<br>
</div>
<br>

<!-- **end egp html banner** -->


<div style="color: white; clear:
both;"/>__,_._,___</div>
</body>

</html>

--1-3257327816-4985630396=:1--


xAP_Automation Main Index | xAP_Automation Thread Index | xAP_Automation Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.