Re: Fw: CBus programming question

["Raymond Kelly" <raymondtkelly@xxxxxxxxx>]

Thanks guys was confused about what is available as 'standard' switch
behaviour out of the box so to speak as opposed to programmable behaviour
for switches. Just want to make sure that I don't purchase too much CBUS
kit
- hard though it is!!

On 04/09/07, Gareth Cook <g@xxxxxxx> wrote:
>
>   If programmed as a dimmer button, yes - standard switch programming
>
> Gareth Cook
> IT Architect / Project Manager, SWG Sales Europe
> Office: +44 (0)1784 445166 - Mobile: +44 (0)7980 445166
> email: g@xxxxxxx <g%40uk.ibm.com>
>
> ----- Forwarded by Gareth Cook/UK/IBM on 04/09/2007 14:21 -----
>
> Discussion
> Main Topic
>
> ukha_d@xxxxxxx <ukha_d%40yahoogroups.com>
> Today 14:07
>
> .
> Subject:
> .
> Re: [ukha_d] CBus programming question
> .
> Category:
>
> Related question.
> Similarly if I press and hold on a CBUS switch this will dim/bright a
> dimming channel? Sorry if this seems an obvious question!!
>
> On 04/09/07, Paul Gordon
<paul@xxxxxxx<paul%40paulgordon.homeip.net>>
> wrote:
> >
> > I don't *think* you'll be able to accomplish that with just the
logic
> > capabilities of the switches/modules themselves since I don't
think
> > there are timers you can use in the programming (It's been a
while since
> > I last touched my CBUS config though, so it's possible I may have
> > forgotten about something!) ... - you might be able to do it
using the
> > short press/long press conditions perhaps?... E.G:
> >
> > 1. lights are off
> > 2. short press turns light 1 on
> > 3a. another short press turns light 1 off again
> > 3b. Or a long press turns light 2 on
> > 3c. Another log press turns light 2 off again
> >
> > You can certainly do this with a CBUS PAC though (or any of the
other
> > units with the logic engine, i.e. the CTOUCH modules).
> >
> > You could also do this with Comfort if you happen to have one....
> >
> > I'm sure Phil H will be along with the *definitive* answer in a
> > while....
> >
> > Paul G.
> >
> > > -----Original Message-----
> > > From: ukha_d@xxxxxxx
<ukha_d%40yahoogroups.com><ukha_d%40yahoogrou
> ps.com> [mailto:
> > ukha_d@xxxxxxx <ukha_d%40yahoogroups.com>
<ukha_d%40yahoogrou
> ps.com>] On Behalf
> > > Of Neil Wrightson
> > > Sent: 04 September 2007 10:59
> > > To: UKHA Group
> > > Subject: [ukha_d] CBus programming question
> > >
> > > Hi All,
> > >
> > >
> > >
> > > A friend of mine has a CBus installation and he wants to
know how to
> > > setup
> > > bathroom lights as per below.
> > >
> > >
> > >
> > > Basically, one switch two lights.
> > >
> > >
> > >
> > > Lights are OFF.
> > >
> > > 1. Pressing the button turns ON the first light.
> > >
> > > 2. Pressing the button again within 5 seconds turns ON the
second
> > > light.
> > >
> > > 3. Pressing the button again turns OFF all lights.
> > >
> > >
> > >
> > > If the period between 1 & 2 is greater than 5 seconds,
then the second
> > > press
> > > turns OFF the lights.
> > >
> > >
> > >
> > >
> > > I have never played with CBus but I do program in various
other
> > > languages.
> > >
> > > So if you can give me some clues, I'm sure I can assist my
friend in
> > > getting
> > > this going.
> > >
> > >
> > >
> > > Neil.
> > >
> > >
> > > [Non-text portions of this message have been removed]
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
>
> [Non-text portions of this message have been removed]
>
> Unless stated otherwise above:
> IBM United Kingdom Limited - Registered in England and Wales with
number
> 741598.
> Registered office: PO Box 41, North Harbour, Portsmouth, Hampshire PO6
3AU
>
> [Non-text portions of this message have been removed]
>
>
>


[Non-text portions of this message have been removed]