Re: Re: FirM & HomeAutomator update [long (and badly written)]

["Frank Mc Alinden" <armagh@xxxxxxx>]

Hi Shane
            yep
nearly there...I  think Andys pretty happy so far with
it....and hopefully soon Graham will put his to the test when he gets his
av
stuff into node 0...........

Thanks
Frank

BTW     John from Genesis have applied to Clipsal for
the lighting
protocol........fingers crossed..
----- Original Message -----
From: "Shane Harrison" <shane.harrison@xxxxxxx>
To: <ukha_d@xxxxxxx>
Sent: Thursday, October 03, 2002 7:18 PM
Subject: RE: [ukha_d] Re: FirM & HomeAutomator update [long (and
badly
written)]


> It sounds like almost time to break out the bubbly - congratulations
and
> thanks for keeping us informed.
>
>
> Shane
>
> > -----Original Message-----
> > From: Frank Mc Alinden [mailto:armagh@xxxxxxx]
> > Sent: Thursday, 3 October 2002 6:43 p.m.
> > To: ukha_d@xxxxxxx
> > Subject: Re: [ukha_d] Re: FirM & HomeAutomator update
[long
> > (and badly written)]
> >
> >
> > Hi All
> >         The issue with
the yellow led coming on  was reported
> > back during my prototype testing 7/7/02 and was caused by the
> > transmit signal being induced into the rx wiring... At the
> > time it didnt effect the operation of the ir system so didnt
> > persue it any further.....
> >     Since then i have reduced the valid start
bit setting in
> > my pic software as it would not recognise my AWA TV remote
> > signals and now when txing a signal it sometimes triggers the
> > busy output......Using a oscilloscope the tx signal can be
> > clearly seen on the rx line......It has no effect as
> > Homevision is transmiiting at that time and therefore the
> > receive mode is either disabled or not polled..............
> >     I have sent the tx signal to my zone 3
via another cat5
> > ,to prove the tx induction and  it works fine ,no yellow
led
> > on or red (busy)...... If it had been a problem ie causing hv
> > to go into a loop i would cable the tx signals with speaker
> > type wire.......
> >
> > When the testing is completed and if everything is ok i hope
> > to have 7 FirM controllers for sale and approx 4 zone rx
> > units + 4 zone splitters per controller . No new boards will
> > be ordered until enough interest is shown as these are quite
> > expensive...
> >
> > Will try and finalise the pricing over the weekend ......
> >
> > Frank Mc
> >
> >
> >
> >
> > ----- Original Message -----
> > From: "Andy Powell" <ukha@xxxxxxx>
> > To: <ukha_d@xxxxxxx>
> > Sent: Wednesday, October 02, 2002 8:17 PM
> > Subject: [ukha_d] Re: FirM & HomeAutomator update [long
(and
> > badly written)]
> >
> >
> > >
> > > Ok, so Frank emailed me...
> > >
> > > "...your resistor explaination was ehhhhhh
bullshit" - so
> > I'd better
> > > let him explain...
> > >
> > > heheheheh
> > >
> > > Andy
> > >
> > >
> > > > Frank and a little test it turns out that having the
resistor was
> > > > what was causing the light to come on... those with
electronics
> > > > experience will understand better than me what is going
on, all I
> > > > know is when the resistor was removed it worked fine. I
should add
> > >
> > >
> > >
> > >
> > > http://www.automatedhome.co.uk
> > > Post message: ukha_d@xxxxxxx
> > > Subscribe:  ukha_d-subscribe@xxxxxxx
> > > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> > > List owner:  ukha_d-owner@xxxxxxx
> > >
> > > List of UKHA Groups here -
> > > http://groups.yahoo.com/group/UKHA_Grouplists/
> > >
> > > Your use of Yahoo! Groups is subject to
> > > http://docs.yahoo.com/info/terms/
> > >
> > >
> >
> >
> > ------------------------ Yahoo! Groups Sponsor
> > ---------------------~--> Home Selling? Try Us!
> > http://us.click.yahoo.com/QrPZMC/iTmEAA/MVfIAA>
/IBOolB/TM
> >
> >
> >
--------------------------------------------------------------
> > -------~->
> >
> http://www.automatedhome.co.uk
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> List of UKHA Groups here -
> http://groups.yahoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
>
>
>
>
>
> http://www.automatedhome.co.uk
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Yahoo! Groups Sponsor

ADVERTISEMENT

http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx 
Subscribe:  ukha_d-subscribe@xxxxxxx 
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx 
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.