RE: Re: FirM & HomeAutomator update [long (and badly written)]

["Shane Harrison" <shane.harrison@xxxxxxx>]

It sounds like almost time to break out the bubbly - congratulations
and
thanks for keeping us informed.


Shane

> -----Original Message-----
> From: Frank Mc Alinden [mailto:armagh@xxxxxxx] 
> Sent: Thursday, 3 October 2002 6:43 p.m.
> To: ukha_d@xxxxxxx
> Subject: Re: [ukha_d] Re: FirM & HomeAutomator update [long 
> (and badly written)]
> 
> 
> Hi All
>         The issue with the
yellow led coming on  was reported 
> back during my prototype testing 7/7/02 and was caused by the 
> transmit signal being induced into the rx wiring... At the 
> time it didnt effect the operation of the ir system so didnt 
> persue it any further.....
>     Since then i have reduced the valid start bit
setting in 
> my pic software as it would not recognise my AWA TV remote 
> signals and now when txing a signal it sometimes triggers the 
> busy output......Using a oscilloscope the tx signal can be 
> clearly seen on the rx line......It has no effect as 
> Homevision is transmiiting at that time and therefore the 
> receive mode is either disabled or not polled..............
>     I have sent the tx signal to my zone 3 via
another cat5 
> ,to prove the tx induction and  it works fine ,no yellow led 
> on or red (busy)...... If it had been a problem ie causing hv 
> to go into a loop i would cable the tx signals with speaker 
> type wire.......
> 
> When the testing is completed and if everything is ok i hope 
> to have 7 FirM controllers for sale and approx 4 zone rx 
> units + 4 zone splitters per controller . No new boards will 
> be ordered until enough interest is shown as these are quite 
> expensive...
> 
> Will try and finalise the pricing over the weekend ......
> 
> Frank Mc
> 
> 
> 
> 
> ----- Original Message -----
> From: "Andy Powell" <ukha@xxxxxxx>
> To: <ukha_d@xxxxxxx>
> Sent: Wednesday, October 02, 2002 8:17 PM
> Subject: [ukha_d] Re: FirM & HomeAutomator update [long (and 
> badly written)]
> 
> 
> >
> > Ok, so Frank emailed me...
> >
> > "...your resistor explaination was ehhhhhh bullshit" -
so 
> I'd better 
> > let him explain...
> >
> > heheheheh
> >
> > Andy
> >
> >
> > > Frank and a little test it turns out that having the
resistor was 
> > > what was causing the light to come on... those with
electronics 
> > > experience will understand better than me what is going on,
all I 
> > > know is when the resistor was removed it worked fine. I
should add
> >
> >
> >
> >
> > http://www.automatedhome.co.uk
> > Post message: ukha_d@xxxxxxx
> > Subscribe:  ukha_d-subscribe@xxxxxxx
> > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> > List owner:  ukha_d-owner@xxxxxxx
> >
> > List of UKHA Groups here - 
> > http://groups.yahoo.com/group/UKHA_Grouplists/
> >
> > Your use of Yahoo! Groups is subject to 
> > http://docs.yahoo.com/info/terms/
> >
> >
> 
> 
> ------------------------ Yahoo! Groups Sponsor 
> ---------------------~--> Home Selling? Try Us! 
> http://us.click.yahoo.com/QrPZMC/iTmEAA/MVfIAA>
/IBOolB/TM
> 
> 
> --------------------------------------------------------------
> -------~->
> 
http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx 
Subscribe:  ukha_d-subscribe@xxxxxxx 
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx 
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here -
http://groups.yahoo.com/group/UKHA_Grouplists/

Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Yahoo! Groups Sponsor

ADVERTISEMENT

http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx 
Subscribe:  ukha_d-subscribe@xxxxxxx 
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx 
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.