The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Using HomeVision with Dallas Temperature sensors


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Using HomeVision with Dallas Temperature sensors
  • From: "Brian Reynolds" <brian.g.reynolds@xxxxxxx>
  • Date: Sat, 4 May 2002 12:33:29 +0100
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

IIRC this calc problem was sorted by upgrading a chip.

Li at Laser was very kind in supplying an upgrade chip for me at some
stage but I cannot remember exactly what it was for!

Sure that is right though.

B.

-----Original Message-----
From: Ian B [mailto:Ian@xxxxxxx]
Sent: 03 May 2002 20:39
To: ukha_d@xxxxxxx Subject: RE: [ukha_d] Using HomeVision with Dallas Temperature sensors


There is some jiggery pokery with a resistor that was mentioned on the
HV
list. If you run into any problems I suggest you ask there.

The temp is also read in farenheight not Celsius. It can do the latter
but I
found calc problems with it which I have not solved yet.

Ian B

> -----Original Message-----
> From: Kenneth Watt [mailto:kennwatt@xxxxxxx]
> Sent: 03 May 2002 19:33
> To: ukha_d@xxxxxxx > Subject: RE: [ukha_d] Using HomeVision with Dallas Temperature sensors
>
>
> Mark,
>
> Have you got the expansion board as you need that?
>
> Other than that it's fairly straight forward to use the Dallas stats
> with HV, or are you trying something a bit different? If I can be any
> help I will but I didn't find much more info than is in the HV bible.
>
> K.
>
> > -----Original Message-----
> > From: Mark Harrison [mailto:Mark.Harrison@xxxxxxx]
> > Sent: 03 May 2002 18:12
> > To: ukha_d@xxxxxxx > > Subject: [ukha_d] Using HomeVision with Dallas Temperature sensors
> >
> > Are the Dallas Temperature sensors listed on the Homevision page
> (DS1820)
> > the same as Dallas 1-wire stuff?
> >
> > If so, is there a good page about actually using them with
Homevision?
> >
> >
> > ------------------------ Yahoo! Groups Sponsor
> >
> > For more information: http://www.automatedhome.co.uk
> > Post message: ukha_d@xxxxxxx > > Subscribe:  ukha_d-subscribe@xxxxxxx > > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx > > List owner:  ukha_d-owner@xxxxxxx > >
> > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
>
>
> For more information: http://www.automatedhome.co.uk
> Post message: ukha_d@xxxxxxx > Subscribe:  ukha_d-subscribe@xxxxxxx > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx > List owner:  ukha_d-owner@xxxxxxx >
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
>
>
>



For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/



Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.