RE: RCS TX15-B Thermostat

["Kevin Hawkins" <lists@xxxxxxx>]

      Peter - the European versions of the TW523
(aka PSC-05) were called
TW7223's and were later superseded by the XM10's. Theses XM10's send
data
slightly differently to the original 523's (some data is sent twice).
The
TW7223 would probably suffice. Let's Automate or Laser are likely
sources
although these 'obsolete' versions may not be listed online. HomeVision
didn't work with the new XM10's correctly without a ROM upgrade.

      BUT I notice you are trying to get hold of
the 253's (sic) but
Kenneth in his post below said that his problem went away when he moved
from
the 253 to an XM10 which is contrary to your experience so I think a
little
more research may be needed into the problem.

      I had a TX15-B here but I am not using it
currently, in fact I
haven't seen it for a while (have just moved house). At that time I used
it
with a TW7223 without I believe any problems. I'll have a rummage and see
if
I can find it and try it with both interfaces. If I remember rightly
there
are some dip switches that set the format in which the thermostat sends
its
status information using extended X10 - is it possible that these are
set
incorrectly ??

      Kevin

>  -----Original Message-----
> From:       Peter Tuckett
[mailto:ptuckett@xxxxxxx] 
> Sent:      28 June 2002 16:34
> To:      ukha_d@xxxxxxx
> Subject:      RE: [ukha_d] RCS TX15-B
Thermostat
> 
> Have tried to find a TW253 interface - any suggestions for
stockists.
> 
>             
-----Original Message-----
>             From:
      Peter Tuckett [mailto:ptuckett@xxxxxxx] 
>            
Sent:      28 June 2002 15:18
>            
To:      ukha_d@xxxxxxx
>            
Subject:      RE: [ukha_d] RCS TX15-B
Thermostat
> 
>             Thanks
Keith. I’ll give that a try
> 
>             Pete
> 
>            
       -----Original Message-----
>            
      From:       Kenneth
Watt
> [mailto:kennwatt@xxxxxxx] 
>            
      Sent:      28 June
2002 12:18
>            
      To:     
ukha_d@xxxxxxx
>            
      Subject:      RE:
[ukha_d] RCS TX15-B Thermostat
> 
>            
      I had the same problem and changing to the
XM10 from
> a TW253 cured the problem for me, the only other thing could be
> interference really or a problem at the PC end.
> 
>            
      K.
> 
>            
      -----Original Message-----
>            
      From: Peter Tuckett
[mailto:ptuckett@xxxxxxx] 
>            
      Sent: 28 June 2002 11:57
>            
      To: ukha_d@xxxxxxx
>            
      Subject: [ukha_d] RCS TX15-B Thermostat
> 
>            
      I have a problem setting up TX15-B, using
xm10e-120,
> with homeseer. Commands are accepted ok but I am unable to get any
status
> information.
> 
>            
      I have checked the interface cable and
changed the
> xm10 with no effect
> 
>            
      Can anyone help
> 
>            
      Thanks
> 
>            
      Pete

Yahoo! Groups Sponsor

ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

<<attachment: winmail.dat>>