The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: H/W Development question


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Conduit to run cable outside



Title: Message
>That sounds good but where did you get the 20mm conduit from? I have looked around and had no luck.
 
 
 
 
 -----Original Message-----
From: Ben McCormack [mailto:ben.mccormack@xxxxxxx]
Sent: 03 January 2002 12:52
To: ukha_d@xxxxxxxSubject: RE: [ukha_d] Conduit to run cable outside

Hi James
 
That sounds good but where did you get the 20mm conduit from? I have looked around and had no luck.
 
I am not going to be running CAT 5 every where at the moment.
 
The cable that I am installing is to run a second set of speakers from my Denon AVR3801 receiver to play radio etc in the bedroom, we plan in install some ceiling speakers to keep it all discrete!
 
I think we are going to use Linn Sweetspot speakers in the bedroom after much looking around, does anyone have any experience of these?
 
While I am here I had better ask another few questions.
 
What would be the best and cheap way of sending IR downstairs, I have spent a bit of time investigating this and the RF solutions do not get good reviews and the wired stuff is expensive, any ideas?
 
Thanks in advance
 
Ben
-----Original Message-----
From: James Hoye [mailto:james.hoye@xxxxxxx]
Sent: 02 January 2002 18:21
To: ukha_d@xxxxxxxSubject: Re: [ukha_d] Conduit to run cable outside

This email was delivered to you by The Free Internet.
http://www.thefreeinternet.net

> James Hoye is doing this TODAY!
 
> James??
 
Well, I ran some 20mm galvanised steel conduit >from TV and FM aerial downleads.
 
Thanks to Mark CAT5 Flipping McCall and you lot with all your bargains (DDAR, TiVo, Book PC) I took the plunge and started cabling with CAT5.  I have spent ALL afternoon getting the RG59 downleads out (going to cable tie CT100 to the conduit instead) and running 4 x CAT5 down it.  It was a real sod because it's about 5m in length (no bends thankfully) and I had to feed the bundle of CAT5s down a few inches at a time on my own.
 
Of course, 20mm conduit restricts you to at maximum 4 x CAT5 (fewer if it has bends, believe me), and you need a special threading (as possibly bending) tool.  It looks OK though.  Mark Harrison has used ventilation ducting (bathroom/kitchen extractor fan stuf) and you can get LOTS of CAT5 in it :)
 
James H


For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


***********************************************************
This message is confidential and intended for the exclusive
use of the addressee(s) only and remains the property of
Exchange FS Group plc. You should not disclose its contents
to any other person. If you are not the intended recipient
please notify the sender named above immediately.

Registered Office: Munro House, Portsmouth Road, Cobham,
Surrey, KT11 1TE. Registered in England No. 2596452
***********************************************************

Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.