RE: Re: Home Vision Question

["Keith Doxey" <ukha@xxxxxxx>]

Have you seen "Ron Hazeltons Housecalls" on Discovery Home and
Leisure?

I could get a Winnebago and tour the country doing "Keith Doxey's
Automation
Calls" :-)

Keith

> -----Original Message-----
> From: geraint@xxxxxxx [mailto:geraint@xxxxxxx]
> Sent: 07 August 2001 22:52
> To: ukha_d@xxxxxxx
> Subject: [ukha_d] Re: Home Vision Question
>
>
> Same idea as I had,,,,but my electronics weakness is my downfall.
>
> What I need is an electonics wiz for hire !!!!!
> We need to clone Mr Doxey and then send him round to people's houses
> and lock him in until it is all complete.
>
> I'm thinking of having a comfort system fitted, BUT NOT BY ME !
> I wonder if the guys Andrew recommended for the install would be able
> to do these bits and bobs ?
>
> --- In ukha_d@y..., "Kenneth Watt" <kennethwatt@y...>
wrote:
> > Geraint,
> >
> > I too have been looking into this in a bit of depth.
> >
> > I wanted to get the VisAccess
> > (http://www.letsautomate.com/10483.cfm?cfid=46892&cftoken=28318)
> and use
> > that to send a signal to HV to open the doors and re-lock after a
> > pre-determined time. A bit more secure I think than solely
relying
> on
> > X10!
> >
> > HTH
> >
> > K.
> >
> > -----Original Message-----
> > From: geraint@a... [mailto:geraint@xxxxxxx...]
> >
> > Sent: 07 August 2001 19:44
> > To: ukha_d@y...
> > Subject: [ukha_d] Home Vision Question
> >
> > Not got a homevision or even played/seen one.
> >
> > I have just got the first of my electronic locks for the doors...
> >
> > after all the messing around, I have left the standard five lever
> > mortice locks in, but have now purchased electromagnetic ones for
> > daytime convenience.
> >
> > The circuit takes 12v (via transformer) to power the magnet, so I
> was
> > thinking the easiest way was to hook this into an Appliance
Module,
> > wether plug in or Din Rail, so that I could switch off the
circuit
> > thus allowing entrance.
> >
> > Is there a way in Homevision to run a macro off a housecode ?
> >
> > Then I could send an x10 signal to turn off the appliance module,
> but
> > then say 5 seconds later it would turn back on again, thus
securing
> > the door.
> >
> > Thoughts ? Other ways maybe ?
> >
> > Regards
> >
> > Geraint.
> >
> >
> >
> >
> >
> > ____________________________________
> > Automated Home UK
> > http://www.automatedhome.co.uk
> > ____________________________________
> >
> > Post message: ukha_d@y...
> > Subscribe:  ukha_d-subscribe@y...
> > Unsubscribe:  ukha_d-unsubscribe@y...
> > List owner:  ukha_d-owner@y...
> >
> > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> >
> >
> > _________________________________________________________
> > Do You Yahoo!?
> > Get your free @yahoo.com address at http://mail.yahoo.com
>
>
>
>
> ____________________________________
> Automated Home UK
> http://www.automatedhome.co.uk
> ____________________________________
>
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>