Re: Home Vision Question

["Alan Cockerton" <alancc@xxxxxxx>]

How much do you want to spend and what do you want to interface to?
A very good system we use from PAXTON will identify users and allow access
based on predefined criteria, a log is also maintained in a Access
database.

Alancc
----- Original Message -----
From: Mike Griffiths <mike@xxxxxxx>
To: <ukha_d@xxxxxxx>
Sent: Tuesday, August 07, 2001 11:10 PM
Subject: RE: [ukha_d] Home Vision Question


> Anyone know of a system that will identify different users/cards
> Most of the ones I have found only allow common identification
>
> Mike
>
> Sent from Home
>
> -----Original Message-----
> From: Kenneth Watt [mailto:kennethwatt@xxxxxxx]
> Sent: Tue 07 Aug 01 22:44
> To: ukha_d@xxxxxxx
> Subject: RE: [ukha_d] Home Vision Question
>
> Geraint,
>
> I too have been looking into this in a bit of depth.
>
> I wanted to get the VisAccess
> (http://www.letsautomate.com/10483.cfm?cfid=46892&cftoken=28318)
and use
> that to send a signal to HV to open the doors and re-lock after a
> pre-determined time. A bit more secure I think than solely relying on
> X10!
>
> HTH
>
> K.
>
> -----Original Message-----
> From: geraint@xxxxxxx [mailto:geraint@xxxxxxx]
>
> Sent: 07 August 2001 19:44
> To: ukha_d@xxxxxxx
> Subject: [ukha_d] Home Vision Question
>
> Not got a homevision or even played/seen one.
>
> I have just got the first of my electronic locks for the doors...
>
> after all the messing around, I have left the standard five lever
> mortice locks in, but have now purchased electromagnetic ones for
> daytime convenience.
>
> The circuit takes 12v (via transformer) to power the magnet, so I was
> thinking the easiest way was to hook this into an Appliance Module,
> wether plug in or Din Rail, so that I could switch off the circuit
> thus allowing entrance.
>
> Is there a way in Homevision to run a macro off a housecode ?
>
> Then I could send an x10 signal to turn off the appliance module, but
> then say 5 seconds later it would turn back on again, thus securing
> the door.
>
> Thoughts ? Other ways maybe ?
>
> Regards
>
> Geraint.
>
>
>
>
>
> ____________________________________
> Automated Home UK
> http://www.automatedhome.co.uk
> ____________________________________
>
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
> _________________________________________________________
> Do You Yahoo!?
> Get your free @yahoo.com address at http://mail.yahoo.com
>
>
>
>
> ____________________________________
> Automated Home UK
> http://www.automatedhome.co.uk
> ____________________________________
>
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
> ____________________________________
> Automated Home UK
> http://www.automatedhome.co.uk
> ____________________________________
>
> Post message: ukha_d@xxxxxxx
> Subscribe:  ukha_d-subscribe@xxxxxxx
> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
> List owner:  ukha_d-owner@xxxxxxx
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>