[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: Networx NX-590-E



On Apr 6, 8:46=A0pm, "ABLE1" <royboynos...@xxxxxxxxxxxxx> wrote:
> <santiagode...@xxxxxxxxx> wrote in message
>
> news:396aef5e-9776-4505-b005-d7cc5f442410@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
> On Apr 6, 4:45 pm, "ABLE1" <royboynos...@xxxxxxxxxxxxx> wrote:
>
>
>
> > First of all thanks guys for your support on this, so here we go
>
> > my network is very simple I have DSL with ATT, and a linksys router
> > setup with dhcp so the module will take the TCP configuration from
> > it like IP, mask, gateway as well as DNS etc , also the port is setup
> > 10 Full is does not work 100 Full.
>
> > That part is working because I can connect to the module using DL900
> > using an IP and also the module is already enrolled so at this point
> > I believe everything is fine.
>
> > The problems I have are :
> > 1.- I have Aux comm Fail on the Keypad
> > 2.- The module never send emails ,the SMTP servers I am using is
> > ATT.NET but I also test GMAIL and AOL , none of them works with the
> > Module at least for me, for each case I setup the correct smtp
> > server, I=B4m using the hostname for example for @att.netthe server
> > name is smtp.att.yahoo.com and the SMTP port is 465 with
> > ( authentication), Also I tested the configuration using Static IP,
> > and setup the smtp server IP and I got the same results , I am using
> > a mail account that are already in use and fully working like
> > aaaa.b...@xxxxxxx
>
> > Hardware
> > 1.- NX-8E
> > 2.- NX-590e version 2.11
>
> > Internet access details
> > 1.- ATT DSL Moden speed stream 4100 soft ver 1.0.0.53
> > 2.- Linksys router RV082 latest version
>
> > Any advice you can give me will be greatly appreciated, at this
> > point I am running out of ideas. also I=B4am not a network expert.
>
> > Ok, it seems that you have the right stuff and the right info.
>
> > I can't answer the issues of the emails not getting thru since I have n=
ot
> > tried nor do I care to try to make that work.
>
> > Procedurally I would do the following and if it did not communicate I
> > would
> > return it to GE and get another or find a different way to communicate.
>
> > * 8 <CODE> 7 9 # 9 1 0 # EXIT EXIT
> > That will default the board and get a fresh start. Would not hurt to do
> > power cycle at this point.
>
> > Default the Router back to Factory if you can.
> > Explorer................ 192.168.1.1 User Name empty and password: "adm=
in"
> > If you can't call Lynksys.
>
> > Connect CAT5 Cable and make sure it is connected to network.
> > Enter Programming and:
>
> > Then turn on DHCP and Polling.
> > Then enter the IP address into the "Primary Receiver" location.
> > Then enter the Account Number with preceding zeros as in 00001234
> > Exit Exit Programming wait 30 seconds and power cycle system down for 3=
0
> > seconds. >>> VERY IMPORTANT!!!!!!
>
> > Send a signal and see if it arrives. If it does Whoopie!!!! If it does =
not
> > BUMMER and trash the sucker..........
>
> > And if it really does communicate you can then and only then try your
> > email
> > stuff.
>
> > Let me know how it goes.
>
> > Good luck.
>
> > Les
>
> Hi Les
>
> when you say "Send a signal and see if it arrives. " =A0what you really
> means by that,
>
> Whoaaaaa there big fellow!!!!!!!!!!!!!!
>
> Your using your high priced, Hi-Tech Security Panel to do what???? =A0Sen=
d
> emails???
>
> Good luck with that.
>
> Have a nice day.
>
> Les

I knew it,  you guys  has not clue about  how to fix the NX590e
problem so my suggestion is if you don't want to be part of the
solution at least don't be part of the problem,  smart a$$......

sincerely

San


alt.security.alarms Main Index | alt.security.alarms Thread Index | alt.security.alarms Home | Archives Home