Re: PCLink Speed

["Roland" <roland@xxxxxxxxxxxx>]

I never used that model. Usually it is (was) a UDS-10 (now 1100) that gets
used most often around here.
I can think of some reason why it won't work with that software. You might
want to forget using the Lantronix and get the T-Link instead. Just make
sure the ports you need aren't blocked.
Port Usage Table

NOTE: Confirm with the network administrator that the following ports are
locked open and

that the SG-DRL3-IP has network access for all required network segments.

Description

Default

Port #

Programming Location to Change

T-Link TL250/

TL300

T-Link Source Port 3060 Section [009] T-Link options from Keypad

T-Link Destination

Port

3061 Section [010] T-Link options from Keypad

SG-DRL3-IP

T-Link Port 3061 Section [0B] [0C] from Console S/W

DLS Port 3062 Section [0D] [0E] from Console S/W

SA Port 3063 Section [11] [12] from Console S/W

Console S/W Port 3064 Section [14] [15] from Console S/W

DLS2002 DLS Port 3062 Modem Configuration Options

DLS SA SA Port 3063 Modem Configuration Options

Console Console Port 3064

T-Link Console

TFTP Firmware Upgrade 69


8.1 Remote Control

The panel and the DLS software will control this function. The module will
be a conduit for the

information. Commands can be sent from the DLS or SA software to allow
control of the

panel; Arm/Disarm, Bypass/Un-Bypass, Status Request.

NOTE: New DLS-3 and System Administrator drivers are required for the PC5020
v3.2 and

PC4020 v3.31. These drivers can be downloaded free from
dsc.com/dls3drivers.htm. DLS-3

and System Administrator can communicate directly to the T-Link TL250
module. The DLS

software can be used with UL Listed installations only when service
personnel are on-site.


"R-Guy" <ron.20070101@xxxxxxxxxxxxx> wrote in message
news:Ivxnh.556563$5R2.472748@xxxxxxxxxxxx
> It is a SCS100 (http://www.lantronix.com/pdf/SCS100-200-400_UG.pdf).
>
> "Roland" <roland@xxxxxxxxxxxx> wrote in message
> news:459e9d07$0$18058$4c368faf@xxxxxxxxxxxxxxxxx
>> Having been where you are many times I can say that getting a Lantronix
>> unit to work can be vexing at times. Some of the information you request
>> is not listed on the product literature. Which model Lantronix are you
>> using?
>>
>> "R-Guy" <ron.20070101@xxxxxxxxxxxxx> wrote in message
>> news:_Fwnh.562101$R63.237703@xxxxxxxxxxxx
>>>I have a Power832 (PC5010) system and a PC running DLS-2002 SP2.  I also
>>>have a Lantronix single port terminal server and their COM port
>>>redirector software on the PC.
>>>
>>> I idea is to connect to the alarm panel over the LAN rather than running
>>> a serial cable.  The terminal server / redirector software works fine
>>> with other applications, but I have problems getting it going with the
>>> DSC system.  I am suspecting that the problem is the link speed.  The
>>> Lantronix unit does not support 110 bps (just 300 bps and higher).
>>>
>>> Any help would be appreciated.
>>>
>>> "Roland Moore" <roland@xxxxxxxxxxxx> wrote in message
>>> news:459e18fa$0$16983$4c368faf@xxxxxxxxxxxxxxxxx
>>>> Using a PC 5400?
>>>> "R-Guy" <ron.20070101@xxxxxxxxxxxxx> wrote in message
>>>> news:kolnh.555856$5R2.152825@xxxxxxxxxxxx
>>>>> What is the speed of the between a DSC alarm panel (like a PC5010) and
>>>>> a locally connected PC running DLS?
>>>>>
>>>>> Thanks.
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>