Re: Ademco Vista 20 X10 programming question

["Mark Leuck" <m..leuck@xxxxxxxxx>]

That will be real helpful to someone with a fixed english keypad

"Robert L Bass" <RobertLBass@xxxxxxxxxxx> wrote in message
news:kBV4j.22219$AX6.7349@xxxxxxxxxxx
>
> "Bob Sisson" <inspectionsbybob@xxxxxxxxxxx> wrote in message
> news:IIadnR0BCqNsBczanZ2dnUVZ_jqdnZ2d@xxxxxxxxxxxxxx
> > Compass will do X10 Coding ?
> >
> > OK...I have compas, or can get it (my is an older version)
> >
> > Do I need that weird modem still?  (I still have a Hayse 1200b just
> > for my alarm panel)
>
> Programming X-10
>
> 1. Enter program mode by powering down then back up & pressing the
> *+#
>
> simultaneously within 50 seconds of power up, or enter the Installer
> code (4112)
>
> + 8 + 0 + 0.
>
> 2. Screen displays, "INSTALLER CODE 20"
>
> 3. Press "*" 27, screen displays "X10 HOUSE CODE 27" enter the
> desired X-10
>
> House Code. 0=A, 1=B, 2=C, 3=D, 4=E, 5=E, 6=G, 7=H, 8=I, 9=J, #+10=K,
>
> #11=L, #12=M, #13=N, #14=O, #15 =P.
>
> 4. Press "*" 79, screen displays:
>
> Enter Output No.
>
> (00 = Quit) 01
>
> Enter the Device Number 01-18 for Powerline Carrier devices; or 00 to
> end
>
> these entries. Press ? to continue.
>
> 5. Screen displays:
>
> 01 Output Type
>
> Delete 0
>
> Enter 2 for X-10
>
> Press ? to continue.
>
> 6. Screen displays:
>
> 01 Unit No.
>
> 01
>
> Enter the Unit Number for the X-10 device, 01-15
>
> Press ? to continue.
>
> 7. Screen displays:
>
> 01 Enter Output No.
>
> (00 = Quit) 02
>
> Enter 00 to quit or refer back to step 4.
>
> 8. Screen displays:
>
> Enter ? or #
>
> Press ?or # to exit
>
> 9. Enter " 80 "
>
> Screen Displays:
>
> Output Funct #
>
> (00 = Quit) 01
>
> Enter X-10 programming 01-48. Press ? to continue.
>
> 10. Screen displays:
>
> 01 A E P Trig
>
> ?00 0 0 - ZL=00
>
> This is the summary screen, 01=Device #, A=Device Action;
> E=Triggering
>
> Event; P=Partition; Trig=Trigger Type; Press ? to continue.
>
> 11. Screen displays:
>
> 01 Activated By:
>
> Delete 0
>
> Enter the initiating event for this output device:
>
> 1=Zone List (See Step 12)
>
> 2=Zone Type (See Step 13)
>
> 3=Zone Number (See Step 14)
>
> Press ? to continue.
>
> 12. Screen displays:
>
> 01 Zn List
>
> None 0
>
> If a zone list will be used enter the number to be used (01-08);
> NOTE: 9-12 are
>
> used for pagers.
>
> Press ? to continue.
>
> 12a. Screen Displays:
>
> Enter Event
>
> Restore 0
>
> Enter the zone list event that will activate this output:
>
> 0=Restore; 1=Alarm; 2=Fault; 3=Trouble
>
> Press ? to continue, See Step 15 for next program location.
>
> 13. Screen displays:
>
> 01 Enter Zn Type
>
> Zone Disabled 00
>
> Enter the desired zone type, Press ? to continue.
>
> 13a. Choices for Zone Types:
>
> 00=Not Used
>
> 01=Ent/Exit #1
>
> 02=Ent/Exit #2
>
> 03=Perimeter
>
> 04=Interior Follower
>
> 05=Trouble Day/Alarm Night
>
> 06=24 Hr Silent
>
> 07=24 Hr Audible
>
> 08=24 Hr Aux
>
> 09=Fire
>
> 10=Inter w/Delay
>
> 12=Monitor Zone
>
> 14=Carbon Monoxide
>
> 16=Fire W/Verification
>
> 23=No Alarm Response
>
> 24=Silent Burglary
>
> 25=24 Hr Non-Alarm
>
> 77=Keyswitch Zone
>
> 13b. Choices for System
>
> Operation:
>
> 20=Arming Stay
>
> 21=Arming Away
>
> 22=Disarming
>
> 31=End of Exit Time
>
> 32=Start of Entry Time
>
> 33=Any Burg Alarm
>
> 36=**Bell Timeout***
>
> 38=Chime
>
> 39=Any Fire Alarm
>
> 40=Bypassing
>
> 41=**AC Power Failure
>
> 42=**System Bat Low
>
> 43=Comm. Failure
>
> 52=Kissoff
>
> 54=Fire Zone Reset
>
> **Use 0 for Part # (P)
>
> 58=Duress
>
> 60=AAV
>
> 66=Function key ?
>
> 67=Bell Fail
>
> 68=Telco Line Cut
>
> 78=Keyswitch Red LED
>
> 79=Keyswitch Grn LED
>
> ***Or at disarming
>
> ?Use *57 to assign (07)
>
> 13c. Screen displays:
>
> 01 Partition
>
> Any Partition 0
>
> Enter the partition in which this zone type will occur: 0=Any
> partition;
>
> 1=Partition 1; 2=Partition 2; 3=Common, Press ? to continue, see step
> 15 for
>
> next program location.
>
> 14. Screen Displays:
>
> 01 Enter Zn Num.
>
> None 00
>
> Enter the zone number associated with this output number, Press ? to
> continue.
>
> 14a. Screen Displays:
>
> 01 Enter Event
>
> Restore 0
>
> Enter the zone event that will activate this output: 0=Restore;
>
> 1=Alarm/Fault/Trouble
>
> Press ? to continue.
>
> 15. Screen Displays:
>
> 01 Output Action
>
> Off 0
>
> Enter the desired device action as listed below, Press ? to continue.
>
> 0=Off
>
> 1=Close for 2 Seconds
>
> 2=Close & Stay Closed
>
> 3=Continuous Pulse on & off
>
> 4=Toggle State of Relay
>
> 5=Duration 1 (see field 1*77)
>
> 6=Duration 2 (see field 1*77)
>
> 16. Screen Displays:
>
> Enter Output No.
>
> ?00 00
>
> Enter the device output number (programmed in *79 menu mode) you want
>
> associated with this output, Press ? to continue
>
> 17. Screen Displays:
>
> 01 A E P Trig
>
> X01 0 0 - Zn=02
>
> Press ? to continue
>
> 18. Screen Displays:
>
> Output Funct #
>
> (00 = Quit) 02
>
> If programming is complete enter 00 to quit, otherwise refer to step
> 9
>
> 19. Screen Displays:
>
> Enter ? or #
>
> Enter ? or # to exit
>
> 20. Screen Displays:
>
> Field?
>
> Press 99 to exit program mode
>
>
>
>
> --
>
> Regards,
> Robert L Bass
>
> ==============================>
> Bass Home Electronics
> 4883 Fallcrest Circle
> Sarasota · Florida · 34233
> http://www.bassburglaralarms.com
> Sales & Tech Support 941-925-8650
> Customer Service 941-232-0791
> Fax 941-870-3252
> ==============================>
>