[Message Prev][Message
Next][Thread Prev][Thread Next][Message
Index][Thread Index]
Re: Re: T.O.M 10 info to HV
Hi George
> I created a determinator to send a number (215) to variable 35 in
> HV. I then executed the determinator, went into HV and variable 35
> had a value of 215. Am I missing something?
Thats fine....but for instance when tom10 reports a temp reading like 19.2
(c) ;-)
thats 4 bytes ...what i think you are trying to do is say a temp reading
of
80 (f)......is to send this as a single byte so you get 0 to 255 ????? some
form of conversion required here if this is what your after......am i
correct ???
Frank
----- Original Message -----
From: "gmotichka" <gmotichka@xxxxxxx>
To: <ukha_xpl@xxxxxxx>
Sent: Friday, February 11, 2005 11:20 AM
Subject: [ukha_xpl] Re: T.O.M 10 info to HV
>
>
>
> > Using xPL ????????
>
> Well yah, I think so. But now you have me wondering if we are
> talking about the same thing.
>
> I created a determinator to send a number (215) to variable 35 in
> HV. I then executed the determinator, went into HV and variable 35
> had a value of 215. Am I missing something?
>
> George M
>
> PS. using the homevision plug in of course.
>
>
>
>
>
>
>
>
> > Frank
> >
> > ----- Original Message -----
> > From: "gmotichka" <gmotichka@h...>
> > To: <ukha_xpl@xxxxxxx>
> > Sent: Friday, February 11, 2005 10:58 AM
> > Subject: [ukha_xpl] Re: T.O.M 10 info to HV
> >
> >
> > >
> > >
> > > Frank,
> > >
> > > I just tested getting three digit variables from HV and
sending
> thre
> > > digit variable to HV. Although I must say that getting the
> correct
> > > variable number from HV is a chalange for me as it does not
> always
> > > work. I do not know why that is so. However when it does
work it
> > > will definatly work with numbers up to 255.
> > >
> > > George
> > >
> > >
> > >
> > >
> > >
> > > --- In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
> <fmcalind@b...>
> > > wrote:
> > > > Hi George
> > > >
> > > > > Also it would then allow it to be put into a
variable
> because it
> > > > > would then be up to two or three bytes.
> > > >
> > > > How would you pass this via xpl-hvision ???....AFAIK
....it can
> > > only pass
> > > > single byte variables in a single xpl message ???......
> > > >
> > > > Frank
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "gmotichka" <gmotichka@h...>
> > > > To: <ukha_xpl@xxxxxxx>
> > > > Sent: Friday, February 11, 2005 5:33 AM
> > > > Subject: [ukha_xpl] Re: T.O.M 10 info to HV
> > > >
> > > >
> > > > >
> > > > >
> > > > > Steve,
> > > > >
> > > > > Thanks for the insight. But -- if your code were
to do the
> > > > > calculations to F as Frank suggested, that would
not violate
> the
> > > > > stadard would it? I think a lot more F speeking
people :) are
> > > using
> > > > > xPl now also.
> > > > > Also it would then allow it to be put into a
variable
> because it
> > > > > would then be up to two or three bytes.
> > > > >
> > > > > Thanks
> > > > > George
> > > > >
> > > > >
> > > > >
> > > > > -- In ukha_xpl@xxxxxxx, steve.cooper@u... wrote:
> > > > > >
> > > > > > >> I cannot see how to pass the temps
from T.O.M 10 to HV
> > > > > > > Cant see how this could be done at the
moment ,as hv
> > > variables
> > > > > are 1 byte
> > > > > > > and the xPL globals vary in size and the
temp globals
> would
> > > be 4
> > > > > bytes
> > > > > > > ....In my setup i just store the temps
in xPL Globals so
> > > hasnt
> > > > > been a
> > > > > > > problem...not sure if Steve can do
something about
> this.....
> > > > > >
> > > > > > As Frank says not sure how you would load
something like
> 19.6
> > > into
> > > > > a
> > > > > > variable that can have a value 0 to 255.
> > > > > >
> > > > > > > I think the temps are converted in
Justins board to
> > > > > C......Might be
> > > > > > > possible for Steve to add in the tom10
config a tick box
> to
> > > > > enable F
> > > > > > > conversion ????
> > > > > >
> > > > > > This is possible from a code point of view
but I believe
> that
> > > > > there is a
> > > > > > xPL standard that say all temperatures will
be reported in
> C to
> > > > > avoid
> > > > > > confusion. Not sure whether this is
documented but it was
> > > > > certainly the
> > > > > > case from the beginning IIRC.
> > > > > >
> > > > > > S.
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > >
> _____________________________________________________________________
> > > > > ______
> > > > > > Authorised and regulated by the Financial
Services
> Authority
> > > > > >
> > > > >
> > >
> _____________________________________________________________________
> > > > > ______
> > > > > > The information contained in this message is
confidential
> and
> > > may
> > > > > be
> > > > > > legally privileged. If you are not the
intended recipient,
> > > please
> > > > > do not
> > > > > > read, copy or otherwise use it and do not
disclose it to
> anyone
> > > > > else.
> > > > > > Please notify the sender of the delivery
error and then
> delete
> > > the
> > > > > > message from your system.
> > > > > > Any views or opinions expressed in this email
are those of
> the
> > > > > author only.
> > > > > > Communications will be monitored regularly to
improve our
> > > service
> > > > > and for
> > > > > > security and regulatory purposes.
> > > > > > Thank you for your assistance.
> > > > > >
> > > > >
> > >
> _____________________________________________________________________
> > > > > ______
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > > > http://www.xpl.myby.co.uk
> > > > > To Post a Message: ukha_xpl@xxxxxxx
> > > > > To Subscribe: ukha_xpl-subscribe@xxxxxxx
> > > > > To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > >
> > >
> > >
> > >
> > >
> > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > http://www.xpl.myby.co.uk
> > > To Post a Message: ukha_xpl@xxxxxxx
> > > To Subscribe: ukha_xpl-subscribe@xxxxxxx
> > > To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> > >
>
>
>
>
>
> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
http://www.xpl.myby.co.uk
> To Post a Message: ukha_xpl@xxxxxxx
> To Subscribe: ukha_xpl-subscribe@xxxxxxx
> To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
xPL Links: http://www.xplproject.org.uk http://www.xplhal.com http://www.xpl.myby.co.uk
To Post a Message: ukha_xpl@xxxxxxx
To Subscribe: ukha_xpl-subscribe@xxxxxxx
To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
xPL Main Index |
xPL Thread Index |
xPL Home |
Archives Home
|