[Message Prev][Message
Next][Thread Prev][Thread Next][Message
Index][Thread Index]
Re: Re: HV Macro runs multiple times
Hi George
I think Mal (the w800 developer) might need to have a look
at the app.....
Just hang in there it will be sorted soon........
Frank
----- Original Message -----
From: "gmotichka" <gmotichka@xxxxxxx>
To: <ukha_xpl@xxxxxxx>
Sent: Sunday, December 05, 2004 6:43 AM
Subject: [ukha_xpl] Re: HV Macro runs multiple times
>
>
> Yes, Tried as quick as possible on the press -- no difference. Then
> I thought maybe because on the conditions I had "*" for
target, so I
> tried using just "GSHED-HVISION", but then it did not get
passed to
> HV to process.
>
> George
>
>
>
>
>
> In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
<fmcalind@b...>
> wrote:
> > Hi George
> >
> > > Yes, I get multiple messages in the xPL monitor. It usually
> shows 3
> > > instances - yet the macro executes up to 6 times.
> >
> > If its receiving multiple copies of the same command each time a
> button is
> > pressed , a delay may be required to filter out some of the
> repeated
> > commands....I think Mal would need to have a look at this.....
> >
> > I assume you have tried very short presses and still get multiple
> received
> > w800 messages ??
> >
> > Frank
> >
> > ----- Original Message -----
> > From: "gmotichka" <gmotichka@h...>
> > To: <ukha_xpl@xxxxxxx>
> > Sent: Sunday, December 05, 2004 6:25 AM
> > Subject: [ukha_xpl] Re: HV Macro runs multiple times
> >
> >
> > >
> > >
> > > Yes, I get multiple messages in the xPL monitor. It usually
> shows 3
> > > instances - yet the macro executes up to 6 times.
> > >
> > > George
> > >
> > >
> > >
> > >
> > >
> > > --- In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
> <fmcalind@b...>
> > > wrote:
> > > > > I am getting very close on this working. I now
have it where
> the
> > > x10
> > > > > signal is recognized by the W800 and then triggers
the macro
> in
> > > > > HomeVision.
> > > >
> > > > Good news.......
> > > >
> > > > > The problem is that it will execute the macro
multiple
> times --
> > > > > anywhere from 3 to 6 times consecutively. I can
see the
> multiple
> > > > > commands going to HV. I tried to add a 'macro
disable"
> command in
> > > > > the macro, but that did not help. Neither did
adjusting the
> > > ddespeed
> > > > > or lastsent options in the configuration
> > > >
> > > > Are you receiving multiple message in xPL Monitor ??
when you
> > > press a button
> > > > on your rf remote ???......If so The w800-app might
require a
> > > built in delay
> > > > ....Hopefully Mal will post regarding the app.......
> > > >
> > > > Frank
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "gmotichka" <gmotichka@h...>
> > > > To: <ukha_xpl@xxxxxxx>
> > > > Sent: Sunday, December 05, 2004 5:20 AM
> > > > Subject: [ukha_xpl] HV Macro runs multiple times
> > > >
> > > >
> > > > >
> > > > >
> > > > > I am getting very close on this working. I now
have it where
> the
> > > x10
> > > > > signal is recognized by the W800 and then triggers
the macro
> in
> > > > > HomeVision.
> > > > >
> > > > > The problem is that it will execute the macro
multiple
> times --
> > > > > anywhere from 3 to 6 times consecutively. I can
see the
> multiple
> > > > > commands going to HV. I tried to add a 'macro
disable"
> command in
> > > > > the macro, but that did not help. Neither did
adjusting the
> > > ddespeed
> > > > > or lastsent options in the configuration.
> > > > >
> > > > > Further suggestions would be welcomed.
> > > > >
> > > > > Thanks
> > > > > George
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > > > http://www.xpl.myby.co.uk
> > > > > To Post a Message: ukha_xpl@xxxxxxx
> > > > > To Subscribe: ukha_xpl-subscribe@xxxxxxx
> > > > > To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > http://www.xpl.myby.co.uk
> > > To Post a Message: ukha_xpl@xxxxxxx
> > > To Subscribe: ukha_xpl-subscribe@xxxxxxx
> > > To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> > >
>
>
>
>
>
>
> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
http://www.xpl.myby.co.uk
> To Post a Message: ukha_xpl@xxxxxxx
> To Subscribe: ukha_xpl-subscribe@xxxxxxx
> To Unsubscribe: ukha_xpl-unsubscribe@xxxxxxx
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
xPL Main Index |
xPL Thread Index |
xPL Home |
Archives Home
|