The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

RE: Newby - Help with Homeseer /xap/ xLobby


  • Subject: RE: Newby - Help with Homeseer /xap/ xLobby
  • From: "Bill Lott" <lottbill@xxxxxxxxxxxxx>
  • Date: Sat, 14 May 2005 22:41:12 -0400

------=_NextPart_000_0000_01C558D6.07F9E370
Content-Type: text/plain;
charset="us-ascii"
Content-Transfer-Encoding: 7bit

Thanks to all. Homeseer and xLobby are now working together with xap.  Now
for the fun stuff - to be able to update status on both.



_____

From: xap_automation@xxxxxxx [mailto:xap_automation@xxxxxxx]
On Behalf Of James Traynor
Sent: Wednesday, May 11, 2005 8:50 PM
To: xap_automation@xxxxxxx
Subject: Re: [xap_automation] Newby - Help with Homeseer /xap/ xLobby



Bill,

As siliconmeltus mentioned a single wildcard of
mi4.homeseer.servername.*:xxx  seems to work fine. I'm looking in to why
there are issues with *.* It shouldn't make any difference but something
does seem to be stopping it match. I'll look into it and report back.

James

Bill Lott wrote:
> MAYBE I SPOKE TOO SOON! (If after 6 hours it can be too soon....)
>
> Progress and limited success.
>
> I now know the problem - I just don't know how to fix it.
>
> In the xLobby plug-in setup Configuration screen setting General Tab
Box
of
> Destination Address for x10 Command if I use
"mi4.homeseer.homeseer.H" it
> works!  (H4 is x10 address of the Hallways Upstairs light I'm trying
to
> control)  Using the "H: is the answer - before I was trying to
use a
default
> of "Master" instead of "H".
>
> Now here's my problem.  I have over 100 devices on all different house
> codes.  Although using the destination address of
"mi4.homeseer.homeseer.H"
> fixes my problems for "H" house codes, how do I setup the
destination
> address to allow for other house codes??????????
>
> I'm getting excited again...
>
> THANKS!!!
> Bill Lott
>
>
> -----Original Message-----
> From: xap_automation@xxxxxxx
[mailto:xap_automation@xxxxxxx]
> On Behalf Of James
> Sent: Tuesday, May 10, 2005 7:16 PM
> To: xap_automation@xxxxxxx
> Subject: Re: [xap_automation] Newby - Help with Homeseer /xap/ xLobby
>
> Bill,
>
> Hi, and welcome to the group. It looks like you've got all the right
> things installed. I assume it's all on one PC, if not a hub should
> really be running on both computers. In the messages below there are a
> couple of oddities which I presume are just typos but better to check.
> The iUID line should be just UID and above id=* there should be an
> output.state { .
> The next couple of things to try are putting the homeseer plugin in to
> debug mode, in the xAP Conduit>Config menu. Every received xAP
message
> will generate lots of messages in the log. If nothing appears it would
> be worth checking and restarting the hub on that pc. Next step would
be
> to try changeing the target from mi4.homeseer.*.*:Hallways.Light to
the
> full address mi4.homeseer.servername.H:Hallways.Light ( or whatever it
> is) just to see if there are any issues with the wildcarding.
> Hopefully one of these will fix it! Let me know how you get on.
> James
>
> Bill Lott wrote:
>
>
>>I'm new to xap and could use some help. I posted on the xLobby
forum
>>but came here in hopes of success! I'm excited about the
possibilities
>>of xap and my home automation system.
>>
>>I'm attempting to control lights in the house via
Homeseer/xap/xLobby.
>>
>>I have followed the install and have Homeseer plug-in, GUI Hub, and
>>xLobby plug-in installed. The hub sees activities from both. I'm
sure
>>I omitted something stupid but..
>>
>>If I select "Actions on receipt" within the xLobby
plug-in I get
>>windows opening within xLobby showing Homeseer activities so I know
>>there is a connection between xlobby and Homeseer, but I can't get
any
>>actions from xlobby to work with Homeseer.
>>
>>Under the events tab I have created an event called ceiling light
On
>>and configured it as follows:
>>
>>Plug-in: xAP-Xlobby
>>
>>Command: Basic Control: On
>>
>>Variables: Hallways.light
>>
>>When I run this I see the following in the GUI Hub:
>>
>>xap-header
>>
>>{
>>
>>v=12
>>
>>hop=1
>>
>>iuid=FFABCD00
>>
>>class=xAPBSC.cmd
>>
>>source=PTrinchi.Xlobby.homeseer
>>
>>target=mi4.homeseer.*.*:Hallways.Light
>>
>>}
>>
>>id=*
>>
>>state=On
>>
>>}
>>
>>Nothing happens within Homeseer. There is nothing in the HS event
log
>>
>>My device is light under the location of hallways.
>>
>>If I turn the light on within Homeseer, I get a popup window in
xlobby
>>that says
>>
>>xap-header
>>
>>{
>>
>>v=12
>>
>>hop=1
>>
>>iuid=FF411904
>>
>>class=xAPBSC.event
>>
>>source=mi4.homeseer.homeseer.H:Hallways.Light
>>
>>}
>>
>>state:ON
>>
>>
>>------------------------------------------------------------------------
>>*Yahoo! Groups Links*
>>
>>    * To visit your group on the web, go to:
>>      http://groups.yahoo.com/group/xap_automation/
>>    * To unsubscribe from this group, send an email to:
>>      xap_automation-unsubscribe@xxxxxxx
>>
>
> <mailto:xap_automation-unsubscribe@xxxxxxx?subject=Unsubscribe>
>
>>    * Your use of Yahoo! Groups is subject to the Yahoo! Terms of
>>      Service <http://docs.yahoo.com/info/terms/>.
>>
>>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>



_____


xAP_Automation Main Index | xAP_Automation Thread Index | xAP_Automation Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.