The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Fw: GAH ! Soldering expert required Surrey/Berks/Hants


  • Subject: Fw: GAH ! Soldering expert required Surrey/Berks/Hants
  • From: Gareth Cook <g@xxxxxxxxxx>
  • Date: Tue, 1 Jun 2010 11:08:56 +0100

Yes, it was rfxcom. Cytech reckon it may work with their special
firmware,
but I dont fancy spending my cash to test it all out.

For the former, as many as poss. Certainly, I'd like 6 at the moment. You
got a usable switchable remote I can plumb relays into ?


Ah, stop moaning :p

Which 'bloody board' are you waiting on? BBS, or RFXCOM?

If the latter,no joy I'm afraid. (well, one more possibility, but its
unlikely)

If the former, how many channels do you want to swich?

R

On 1 June 2010 10:02, Gareth Cook <g@xxxxxxx> wrote:

>
>
> It's not BBS. But I've been waiting for you to send me that bloody
board
!
> :-)
>
> G.
>
>
> BBS perchance? If so, which model of remote? (I've done 2-way, 6-way
&
> 8-way
> so far. 8-way is a ****
>
> I'm not in your neck of the woods, but if you're doing what I think
you're
> doing, and are prepared to cover cost of remote-control, and sending
it
to
> you - then I'll hapilly do so. No charge for the soldering (Gotta get
you
> hooked 1st, then start charging ;-) )
>
> I wouldn't consider myself a "handy solderer", but have
recently removed
> approx 2000 tiny SMD resistors from PCB's that were built to wrong
spec,
> and
> replaced them all with the correct value. (These SMD devices are small
> enough, that I found two under a finger nail one evening, sometime
after
> arriving home. Not because I felt them, just spotted them - and I keep
my
> nails short, so's not to scratch myriad touch screen devices!
("normal"
> tweezers are too chunky to put them in place for soldering, which is
done
> under a magnifying loupe!!
>
> R.
>
> On 27 May 2010 20:57, Gareth Cook <g@xxxxxxx
<g%40uk.ibm.com>> wrote:
>
> >
> >
> > It's driving me bonkers ! I have failed to solder some wires onto
a
> board
> > that I need :-(
> >
> > Is there anyone in the surrey , berks, or hampshire area that is
a
very
> > handy solderer - I need 6 wires attached to a small remote
control.
> >
> > Thanks !
> >
> >
> > Unless stated otherwise above:
> > IBM United Kingdom Limited - Registered in England and Wales with
number
> > 741598.
> > Registered office: PO Box 41, North Harbour, Portsmouth,
Hampshire PO6
> 3AU
> >
> > [Non-text portions of this message have been removed]
> >
> >
> >
>
> --
> Rob Iles
>
> Harmony - www.domialifestyle.com
> Twitter: http://twitter.com/Rob_Iles
>
> [Non-text portions of this message have been removed]
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
> Unless stated otherwise above:
> IBM United Kingdom Limited - Registered in England and Wales with
number
> 741598.
> Registered office: PO Box 41, North Harbour, Portsmouth, Hampshire PO6
3AU
>
> [Non-text portions of this message have been removed]
>
>
>



--
Rob Iles

Harmony - www.domialifestyle.com
Twitter: http://twitter.com/Rob_Iles


[Non-text portions of this message have been removed]



------------------------------------



UKHA_D Main Index | UKHA_D Thread Index | UKHA_D Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.