RE: [OT] Recovering Com4

["Paul Gale" <groups@xxxxxxxxxxxxxxxx>]

So if it's working - should be OK?

Paul.



> -----Original Message-----
> From: Frank Mc Alinden [mailto:fmcalind@xxxxxxx]
> Sent: 03 March 2005 09:05
> To: ukha_d@xxxxxxx
> Subject: Re: [ukha_d] [OT] Recovering Com4
>
>
> Hi Paul
>
> > What you haven't said is how it was created in the first place -
is it a
> USB to serial converter >etc? The device or program that installed
it
> could
> be run again?
>
> I dont recall how it was created........
>
> I just started up cgate and it opened com4 via a mss unit and is
connected
> ok ;-).....But if i look in the device manager it still doesnt exsist
> ...........Maybe when i reboot next time it will show up ???
>
> Thanks
> Frank
>
>
>
> ----- Original Message -----
> From: "Paul Gale" <groups@xxxxxxx>
> To: <ukha_d@xxxxxxx>
> Sent: Thursday, March 03, 2005 7:57 PM
> Subject: RE: [ukha_d] [OT] Recovering Com4
>
>
> >
> > What you haven't said is how it was created in the first place -
is it a
> USB to serial converter etc? The device or program that installed it
could
> be run again?
> >
> > Paul.
> >
> >
> >
> > > -----Original Message-----
> > > From: Frank Mc Alinden [mailto:fmcalind@xxxxxxx]
> > > Sent: 03 March 2005 08:41
> > > To: ukha_d@xxxxxxx
> > > Subject: Re: [ukha_d] [OT] Recovering Com4
> > >
> > >
> > > Hi Paul
> > >             Com4 is a virtual port so scanning the hardware
isnt going
> to
> > > pick it up iwould imagine and i have previously scanned the
hardware
> and
> > > had
> > > to reboot the computer as it kept scanning and
scanning......
> > > Thanks
> > > Frank
> > >
> > > ----- Original Message -----
> > > From: "Paul Gale" <groups@xxxxxxx>
> > > To: <ukha_d@xxxxxxx>
> > > Sent: Thursday, March 03, 2005 7:37 PM
> > > Subject: RE: [ukha_d] [OT] Recovering Com4
> > >
> > >
> > > >
> > > > Is this on XP? Do a rescan of hardware and it should be
found again.
> > > >
> > > > Serial ports are a bit dodgy sometimes though - you can
get in a
> > > situation
> > > where a com port number is reserved and you have to remove
it
> manually.
> > > >
> > > > Paul.
> > > >
> > > > > -----Original Message-----
> > > > > From: Frank Mc Alinden [mailto:fmcalind@xxxxxxx]
> > > > > Sent: 03 March 2005 08:19
> > > > > To: ukha_d@xxxxxxx
> > > > > Subject: [ukha_d] [OT] Recovering Com4
> > > > >
> > > > >
> > > > > Hi
> > > > >     Sorry for the OT post..........I accidently
uninstalled my
> com4
> as
> > > it
> > > > > was setup for usb and i assumed the uninstall
would only remove
> the
> > > > > usb...Have actually removed com4 (not a physical
port)...any ideas
> how
> > > i
> > > > > can
> > > > > re install it as its been removed from the the
device manager
> table..
> > > > > Thanks
> > > > > Frank
> > > > >
> > > > > www.armaghelectrical.com.au
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>