The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

RE: Hauppauge card giving me a shock


  • Subject: RE: Hauppauge card giving me a shock
  • From: "David" <david@xxxxxxxxxxxxxxx>
  • Date: Wed, 3 Nov 2004 22:32:45 +1300


Geez it=92s amazing what ya learn on here :-)

=20

-----Original Message-----
From: anthony.kirrane@xxxxxxx [mailto:anthony.kirrane@xxxxxxx]

Sent: Wednesday, 3 November 2004 8:50 p.m.
To: ukha_d@xxxxxxx
Subject: RE: [ukha_d] Hauppauge card giving me a shock

=20

Thanks Keith

At last I understand why!=20

Regards

Anthony



-----Original Message-----
From: Keith Doxey [mailto:ukha@xxxxxxx]=20
Sent: 02 November 2004 20:34
To: ukha_d@xxxxxxx
Subject: RE: [ukha_d] Hauppauge card giving me a shock


Hi Anthony

A couple of posts amalgamated together below for ease of reply :-)

Shocks from Aerial leads is quite common. The cause is that the majority
of
domestic video kit eg TV's and VCR's/Satellite receivers are double
insulated do not require an earth connection. However, they also contain
switch mode power supplies and these almost always leak a small amount
of
mains current to the accessable circuitry, this is not a fault, just an
undesireable "feature". This leakage current is within safe
limits but
can
at times give you a tingle.

Where it causes problems is when you have multiple pieces of equipment
connected together as it makes the total leakage current greater thereby
giving a more noticeable shock. Chris commented that boosters
"cause"
shocks. Well sort of..... because the main reason for having a booster
is to
drive multiple sets, it follows that there will be multiple leakage
currents
making the total leakage higher. Actually a booster can lessen or
eliminate
the effect as many of them have an earth connected which kills the
leakage
totally.

The reason for the sparks is that the PC case is earthed and the high
voltage (but extremely low current) on the aerial lead is arcing across.

It isnt really anything to worry about, just be aware of it and try not
to
touch both sides of the the circuit (eg plug in one hand, other hand on
PC
case) when inserting the plug.

Of course, if the sparks are similar to the arc from a MIG welder then
you
do have a bit of a problem :-)

Hope that helps

Keith


> -----Original Message-----
> From: anthony.kirrane@xxxxxxx
[mailto:anthony.kirrane@xxxxxxx]
>
> I began to notice that the TV picture on my kitchen PC would, over
time,
> become worse and worse.  I went to check the aerial cable going into
the
> Hauppauge PVR 350 card and I got a very noticeable electric shock.  I
> thought, oh well some static that had caught me by surprise.  Then I
got
> another one.  I noticed that if I run the coaxial plug across the
metal
> casing of my PC (I know - I know!) I can visibly see little blue
> sparks.  I don't get this behaviour from any of the other aerial leads
> which are all coming from a single booster.
>

> From: christopher purves [mailto:CHRIS_PURVES@xxxxxxx]
> I have found boosters cause the shocks - too much amplification
perhaps.
> Certainly I used to get shocks all the time in my old house. Different
> ground levels perhaps.







UKHA_D Main Index | UKHA_D Thread Index | UKHA_D Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.