The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Re: Automating a combi boiler


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Re: Automating a combi boiler
  • From: "Neil Ball" <neilball@xxxxxxx>
  • Date: Mon, 19 Jan 2004 10:04:25 -0000
  • Mailing-list: list ukha_d@yahoogroups.com; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Take a look at the boiler wiring info - there should be terminals for a
"Central Heating timeclock" or similar which may have a link in
at present.
It will require a 240v relay to switch this, but this will enable you to
remote switch the central heating without disturbing the hot water ie the
boiler remains permanently supplied. All you then need to take care of is
the thermostatic room control which I assume you're doing through HV or
similar.

-----Original Message-----
From: Brian G. Reynolds [mailto:brian.g.reynolds@xxxxxxx]
Sent: Saturday, January 17, 2004 02:25
To: ukha_d@yahoogroups.com
Subject: RE: [ukha_d] Re: Automating a combi boiler


Thanks Patrick for the info,

You say "Not sure what else you were expecting" to my comment
below...well I
was expecting to see "connect HV here"!!!

Haven't these boiler makers heard of HV yet? shame on them...

Cheers mate, I will look into this when I get up later...

B.


-----Original Message-----
From: Patrick Lidstone [mailto:patrick@xxxxxxx]
Sent: 16 January 2004 13:25
To: ukha_d@yahoogroups.com
Subject: [ukha_d] Re: Automating a combi boiler


--- In ukha_d@yahoogroups.com, "Brian G. Reynolds"
<brian.g.reynolds@n...> wrote:
> Hi all,
>
> I have recently installed a new "Protherm 100EC" combi and
am well
pleased with it as I now have a shower!!!.
>
> Question is, can I connect an HV controlled relay to the thermostat
wires to automate it instead of a thermostat?
>
> Somehow I doubt it would be this easy but one lives in hope!

Yes, it is this easy. You may want to consider installing a real
thermostat as a backup, and then setting the set-point to a very low
temperature when using your automated control. Your automated control
and the thermostat should be wired to the boiler in parallel. You
should also ensure that your relay is wired such that the contacts
are left open under controller power-fail conditions, otherwise you
could end up cooking if something goes horribly wrong with your HV
controller!

The switching voltage for the thermostat depends on the boiler. You
may well need to use a mains rated relay/cable.

> I assume a thermostat is just a bi-metallic switch of some sort?

This is correct.

> The manual shows a link that must be removed if a thermostat is
fitted but that is all I can see.

Not sure what else you were expecting.





[Non-text portions of this message have been removed]


UK Home Automation Meet 2004 - BOOK NOW!
http://www.ukha2004.com

http://www.automatedhome.co.uk
Post message: ukha_d@yahoogroups.com
Subscribe:  ukha_d-subscribe@yahoogroups.com
Unsubscribe:  ukha_d-unsubscribe@yahoogroups.com
List owner:  ukha_d-owner@yahoogroups.com


Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.