RE: RE: Nigel Orrs IR and Ians PC circuit

[ian.bird@xxxxxxx]

Stuart

Could you do a digital picture of the one we made up for you. I remember
it was ludicrously simple and a picture is worth a thousand words.

Ian







Stuart Whyte <lists@xxxxxxx>
25/04/2003 12:20
Please respond to ukha_d


To:     "'ukha_d@xxxxxxx'" <ukha_d@xxxxxxx>
cc:
Subject:        RE: [ukha_d] RE: Nigel Orrs IR and Ians PC circuit


Rob

>From memory I thing it is the rts line from the serial port.  This goes
through a resistor to a transistor.  The output from the transistor goes
to
the bus line on the ir circuit.  You must also common the grounds on the
other side of the transistor, the serial port and the IR circuit.

Hope this comes out ok:

Transistor                              IR
Circuit

/-------------Bus
/
Serial port(RTS)---------resistor---------
\
Serial port(Grd)---------------------------\-------------Grd

HTH

Stuart


-----Original Message-----
From: Robert Chasmer [mailto:robert.chasmer@xxxxxxx]
Sent: 25 April 2003 12:10
To: 'ukha_d@xxxxxxx'
Subject: RE: [ukha_d] RE: Nigel Orrs IR and Ians PC circuit


ian.bird@xxxxxxx wrote:
> Your current board(s) will have a power supply somewhere to make them
> work. This power supply gives the bus power and the TSOP's simply
> grounds  or doesn't ground this bus. The bus is connected to the 555
> chip which is turned on and off depending on the bus state.
> The PC connection simply emulates the TSOP. From the serial port
> one of the connections is used to feed the base of a transistor
> (switch) through a resistor and this switch grounds or otherwise
> the bus.

Stuart/Ian thanks for your replies.  I think I understand nigels circuit
and
what the TSOPs do.  The TSOPs pull the bus low during IR activity, and so
I
need the serial port to do the same thing.  But could I have a little more
detail please on how the serial port will act like a TSOP.

The IR sender circuit I have already has transistor switch feeding the
trigger on the 555 timer as per Nigels diagram
http://www.geocities.com/nigelorr/ir_extend.html.
 So coming out of the
serial port do I need an additional transistor switch, and what pin on the
serial port is supposed to feed it (Is it pin 3 Tx?).  A little diagram
showing what components to use and how to connect them up would be a great
help.

I think my main problem is the limited electronics knowledge I have is all
mixed up and wolley.


> The only common connection is ground which has to be connected
together
> so both devices are batting on the same 'ground' (excuse the pun).

:-) Ok, my bus consists of +12v, signal, 0v.  Each reciever/transmitter
circuit can have its own power, but they need to share the signal and 0v.


Rob

I feel like I need to go back to school and learn all about electronics
again.  It all seems like years ago... well it was :-(

**************************************************************
Franklin + Andrews is a business name of Franklin & Andrews Limited
(Registered in England No 4408389), whose registered office is at St Anne
House, Wellesley Road, Croydon, CR9 2UL

This email message and accompanying data transmitted with it are for the
sole use of the intended recipient(s) and may contain information that is
confidential. If you are not the intended recipient(s), you are notified
that any use, dissemination, disclosure, distribution or copying of this
message or data is prohibited.  If you have received this email message in

error, please notify us immediately and erase all copies of this message
and attachments.


[Non-text portions of this message have been removed]



** UKHA2003 BE THERE! Details here: http://www.automatedhome.co.uk/article.php3?story_id=1110
**
http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/






[Non-text portions of this message have been removed]