The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Can some kind electronics bod help?


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Can some kind electronics bod help?
  • From: "Paul S. Gale" <groups@xxxxxxx>
  • Date: Wed, 5 Feb 2003 09:42:55 -0000
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Can you give me an example description or part number or something for
the opto - I can then have a look to see how much they are here.



Also thinking about patching in IR to a zone that doesn't have a wall
controller fitted (master controller that controls all zones). Has the
same connection for a controller, it's just I'm not using one. Would the
opto route still work i.e. not connecting across the existing lines but
using it instead of a wall controller?



Paul.



-----Original Message-----
From: Frank Mc Alinden [mailto:armagh@xxxxxxx]
Sent: 05 February 2003 09:38
To: ukha_d@xxxxxxx Subject: Re: [ukha_d] Can some kind electronics bod help?



Hi Paul

> Do I need to use an opto. The original poster used a simple transistor
-
> will this not work as well?

Im sure it would work but you need to know for sure what you are
doing..Using the opto couplers will give electrical isolation between
the 2
pieces of equipment....Two very expensive peices of equipment as well
...

Frank

----- Original Message -----
From: "Paul S. Gale" <groups@xxxxxxx>
To: <ukha_d@xxxxxxx>
Sent: Wednesday, February 05, 2003 8:24 PM
Subject: RE: [ukha_d] Can some kind electronics bod help?


> Do I need to use an opto. The original poster used a simple transistor
-
> will this not work as well?
>
>
>
> Paul.
>
>
>
> -----Original Message-----
> From: Frank Mc Alinden [mailto:armagh@xxxxxxx]
> Sent: 05 February 2003 07:25
> To: ukha_d@xxxxxxx > Subject: Re: [ukha_d] Can some kind electronics bod help?
>
>
>
> Hi Shane
>                 On  the original post the guy mentions that the ocelet
> has
> open collector outputs and that the Kustom system  wqs looking for 5v
> signal..So Paul has the same problem..if an opto is used ..Tie the
> collector
> to +5v via say 100 ohm resistor and connect the emitter to the zone tx
> line.....Some connection diagrams might help??
>
> Frank
> ----- Original Message -----
> From: "Shane Harrison" <shane.harrison@xxxxxxx>
> To: <ukha_d@xxxxxxx>
> Sent: Wednesday, February 05, 2003 6:08 PM
> Subject: RE: [ukha_d] Can some kind electronics bod help?
>
>
> > See comments below
> >
> > > -----Original Message-----
> > > From: Paul S. Gale [mailto:groups@xxxxxxx]
> > > Sent: Wednesday, 5 February 2003 1:36 a.m.
> > > To: ukha_d@xxxxxxx > > > Subject: RE: [ukha_d] Can some kind electronics bod help?
> > >
> > >
> > > Yes - it seems that the Kustom amp is based on 5V IR signals
> > > - how could I tell for sure without a scope? Would a digital
> > > multimeter give an accurate enough reading on the IR lines?
> > > (or should the IR output from the wall controller be the same
> > > voltage as the supply voltage?)
> >
> > If you are lucky and the Kustom input has an internal pullup
> > (essentially a resistor to the power rail) then the input will sit
at
> > the power rail voltage when no signal is applied to it.  If it has
no
> > internal pullup then pretty hard to tell with out scoping the the
> > existing IR signal being fed in.
> > >
> > >
> > >
> > > As both Kustom and HV seem to use 5V, should I just try it
> > > without any electronics? Given they're both 5V could I do any
> > > damage? Is all this talk of transistors not needed as both
> > > systems run at 5V?
> > If the HV expansion board is open collector as Frank thinks, then
you
> > can't really do any damage if you connect them together.  However
with
> > open collector outputs (essentially it is a switch to ground only,
> > either the output is grounded or not grounded (floating)) you need
> > something to "pull" the signal up to a positive voltage when the
open
> > collector "switch" is not switched to ground.  This can be an
external
> > resistor (say 10K) or if you are lucky the Kustom has internal
pullups
> > as discussed above.
> >
> > HTH (and makes sense)
> >
> > Shane
> >
> >
> > http://www.automatedhome.co.uk
> > Post message: ukha_d@xxxxxxx > > Subscribe:  ukha_d-subscribe@xxxxxxx > > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx > > List owner:  ukha_d-owner@xxxxxxx > >
> > List of UKHA Groups here -
> http://groups.yahoo.com/group/UKHA_Grouplists/
> >
> > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> >
> >
>
>
> http://www.automatedhome.co.uk
> Post message: ukha_d@xxxxxxx > Subscribe:  ukha_d-subscribe@xxxxxxx > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx > List owner:  ukha_d-owner@xxxxxxx >
> List of UKHA Groups here -
> http://groups.yahoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to the Yahoo!
> <http://docs.yahoo.com/info/terms/>  Terms of Service.
>
>
>
> [Non-text portions of this message have been removed]
>
>
> http://www.automatedhome.co.uk
> Post message: ukha_d@xxxxxxx > Subscribe:  ukha_d-subscribe@xxxxxxx > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx > List owner:  ukha_d-owner@xxxxxxx >
> List of UKHA Groups here -
http://groups.yahoo.com/group/UKHA_Grouplists/
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
>


http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here -
http://groups.yahoo.com/group/UKHA_Grouplists/

Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/>  Terms of Service.



[Non-text portions of this message have been removed]


http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx
List of UKHA Groups here - http://groups.yahoo.com/group/UKHA_Grouplists/


Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.