The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Anyone got Silent Gliss Curtain tracks?


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Anyone got Silent Gliss Curtain tracks?
  • From: "Paul Gale" <groups@xxxxxxx>
  • Date: Fri, 31 Jan 2003 12:48:09 -0000
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

The track has now been replaced with a sturdy metal one. The fixings at the
end and the housing of the motor seem rather poorly designed and not up to
the quality standard I would expect from such an expensive item. From what
you describe, the material band inside seems to be the same - I'll look out
for wear. Apparently this track has a 3 year guarantee though.



Paul.



-----Original Message-----
From: Robert Chasmer [mailto:robert.chasmer@xxxxxxx]
Sent: 31 January 2003 10:28
To: 'ukha_d@xxxxxxx'
Subject: RE: [ukha_d] Anyone got Silent Gliss Curtain tracks?



> From: Paul Gale [mailto:groups@xxxxxxx]
> *      There was a small plastic part (like a cover) holding the
> tensioned band (that moves within the track) together and this
> was broken
> My main reason for posting this is to see if anyone else has had
> a problem with the plastic cover holding the two ends of the
> moving band together? The band is under tension (about 2cm movement
> when untensioned) which is held in place by a very small and weak
> bit of plastic - not good engineering :-(

I have to original Swish versions rather than the new upgraded Silent Gliss
versions.  I bought them when they were runing down the last of the stock at
B&Q, I did have to replace one of my rails that was broken like you
described.

My rail is made complely of plastic, with ends being blobs of plastic which
are fixed by screws into the main rail.  Inside, at either end is a plastic
cog thing which interlocks with a material tape that is hole punged to form
a chain like thing.  The idea is that you could adjust the lengths on them,
which I have done during a repair on one of my rails

The plastic bits that you descibe on mine are held in by plastic lugs which
have been prone on one of my rails of poping out.  One of my rails over a
normal windows has not had any problems in two years.  The other one over
the patio door that has longer and thus heavier curtains did have problems.
To stop the plastic things poping out I drilled a number of small holes and
inserted nails.

About a year in on the big curtian, the rail had completly died.  I nearly
replaced the tape inside since the holes had gotten to large and worn, also
one of the plastic cogs had worn right down.  In the end I just swapped the
driving cog with the one at the other end, and turned the tape round so that
the other side could have some ware.  A year on and its still ok, if I get
more problems I won't hesitate to buy some new cogs and tape.  I did have a
contact number for these and found it to be quite expensive but a lot newer
than a whole new silent gliss pack.

I was under the impression that Silent Gliss had upgraded the tracks
completly and made them metal with better chains inside.  I wanted to just
get new rails from silent gliss, but they will only sell them altogether.  I
already had the motors and controller so didn't want to replace the whole
lot unless I had to.

Let us know how you get on.  In general these rails have been very reliable,
mine are configured to close at night and open in the morning.  The design
of the swish tracks was VERY cheap and nastey, I'd hoped silent gliss had
sorted that part.  For the cost of it there the rails should be built as
well as the motor, and controller.


Rob
--
     ______   __   _   ______   ______
    / ___  / /  / / __   / _____ HOME: rob@xxxxxxx    / /  /_/ / /__/ / / /__/ / / /__    http://www.kaosuk.co.uk/
  / /  __  / ___  / / ___  /  \__  \            ----          
/ /__/ / / /  / / / /  / / _____/ / Rob Chasmer, MMT Computing
______/ _/  /_/ _/  /_/ ______/ robert.chasmer@xxxxxxx
This email and any files transmitted with it are confidential and intended
solely for the use of the individual or entity to whom they are addressed.
If you have received this email in error please let us know by e-mail reply
and delete it from your system; you may not copy this message or disclose
its contents to anyone.  Please note that any views or opinions presented in
this email are solely those of the author and do not necessarily represent
those of MMT Computing plc.  Finally, the recipient should check this email
and any attachments for the presence of viruses.  MMT Computing plc accepts
no liability for any damage caused by any virus transmitted by this email.






Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.