The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: Re: Re: A Question about X10.


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: RF interference



The problem with taboo channels is that they mix together and create
interference frequencies that affect other channels. Every device with a
feed through modulator also amplifies the incoming signal slightly.

It could be that with TiVo in circuit the overall RF level is too high.

You can get plug in attenuators that cut the RF level by 6dB or 12dB. I have
had to use some of these before my RF distribution amp otherwise some
channels suffer strange artifacts.

As a first step (ie Zero cost) I would suggest plotting your channels on the
Taboo TV guide.

If that fails you need to try attenuation at various points in the RF chain
to find the optimum place to cut the level.

The best way is with proper measuring equipment but that cost loadsamoney
:-(

Keith

www.diyha.co.uk
www.kat5.tv


-----Original Message-----
From: BUTLER, Tony, FM [mailto:tony.butler@xxxxxxx]
Sent: 03 July 2002 10:23
To: 'ukha_d@xxxxxxx'
Subject: RE: [ukha_d] RF interference


> I said that as an example.  If your picture goes from good to
> pants just by
> routing thru the TiVo this sounds exactly like a taboo
> channel problem.  The
> fact that you've tried 21 and 69 is meaningless unless you
> know all the
> channels you are receiving and place TiVo on a non taboo one.

I don't see that it is meaningless.
Let's say I stick tivo in and it affects one channel - C5.
I move Tivo to channel 21 and C5 is still affected
I move Tivo to channel 69 and C5 is still affected

This, to me means that whether Tivo is modulating out to 21 OR to 69, the
interference is still there and thus the Tivo channel is _not_ the problem
because I have used two widely separated channels with still the same
effect.

Without Tivo, the TV is presented with N RF channels.
Add in Tivo and it should be N+1 RF channels - ie just the addition of the
Tivo channel.
Or are you suggesting that Tivo is remodulating ALL incoming channels to
different channels so I have 2 x N channels + 1 for the Tivo output of
recorded material?



Tony


********************************************************************
      Visit our Internet site at http://www.rbsmarkets.com

This e-mail is intended only for the addressee named above.
As this e-mail may contain confidential or privileged information,
if you are not the named addressee, you are not authorised to
retain, read, copy or disseminate this message or any part of it.
********************************************************************

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx Subscribe:  ukha_d-subscribe@xxxxxxx Unsubscribe:  ukha_d-unsubscribe@xxxxxxx List owner:  ukha_d-owner@xxxxxxx
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/



Yahoo! Groups Sponsor

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.