The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Idea for IR zoning with HV


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Power Adapter cord length extension


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Power Adapter cord length extension
  • From: "Phil Harris" <phil@xxxxxxx>
  • Date: Tue, 16 Apr 2002 22:06:23 +0100
  • Delivered-to: ukha_archive@xxxxxxx
  • Delivered-to: mailing list ukha_d@xxxxxxx
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Title: Message
Might be unlikely but on the bottom of my DECT basestation (BT Synergy 2120 if anyone else has one) are two, four way RJ11 connectors. Foolish design or not that is what is there. The two connectors can be swapped over physically but obviously I wouldn't want to say what would happen electrically if you did!
 
Phil
-----Original Message-----
From: Aidan Williamson [mailto:fluff@xxxxxxx]
Sent: 16 April 2002 21:29
To: ukha_d@xxxxxxxSubject: RE: [ukha_d] Power Adapter cord length extension

Unlikely to be RJ11 power on a phone, too much risk that someone will plug the power into the line socket (as most phones use RJ11 for phone as per american standard)
 
A.
-----Original Message-----
From: Phil Harris [mailto:phil@xxxxxxx]
Sent: 16 April 2002 19:32
To: ukha_d@xxxxxxxSubject: RE: [ukha_d] Power Adapter cord length extension

The connector is an RJ11 ... not an RJ45.
 
You should be able to get an RJ11 to RJ11 extension cable off the shelf from any phone shop...
 
Phil
-----Original Message-----
From: Eric de Oude [mailto:eric.de.oude@xxxxxxx]

Subject: [ukha_d] Power Adapter cord length extension

Hi All – I wonder if you can offer some advice

 

I have a Phillips DECT phone. The AC adapter (I guess what you guys refer to as a wall wart??) has a standard RJ45 connector at the end of the cable. The RJ45 connector plugs into the base station to provide power.

 

I’d like to extend the power cable so that I can run it in some trunking and keep it tidy. Of the eight pins on the connector, only the outside four are wired. The middle four are not wired.

 

The way I see it I can build some kind of extension keeping the original intact, or lob off the connector (taking note of the pin-outs) and connect some sort extension cable. I’ve done some CAT5 crimping and have the required crimping tools.

 

Any advice? Will the power run over std CAT5?

 

Thanks

 

Eric



For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.