The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Flow switches


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: CAT5 Standard EIA/TIA T568B Wiring Diagram WAS RE: Patch Panels


  • To: "'ukha_d@xxxxxxx'" <ukha_d@xxxxxxx>
  • Subject: RE: CAT5 Standard EIA/TIA T568B Wiring Diagram WAS RE: Patch Panels
  • From: "James, Daniel" <daniel.james@xxxxxxx>
  • Date: Thu, 15 Nov 2001 14:18:29 -0000
  • Delivered-to: mailing list ukha_d@xxxxxxx
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Title: Neil Frost Stationery
Now I may have missed something here, but does this mean I could connect two PC's together without a hub:
 
>Creating a crossover cable
>Crossover cables are used to connect two machines without the use of a hub, switch, or router. While similar to a standard
>CAT 5 cable, the wiring in a crossover cable is actually quite different. Instead of following the same wire pattern on both ends 
>of the cable, one end is exactly opposite of the other, as seen in Table 2 and Figure B below.
 
Dan
 
-----Original Message-----
From: Frost Neil [mailto:neil.frost@xxxxxxx]
Sent: 15 November 2001 14:14
To: HomeAutoGroup (E-mail)
Subject: [ukha_d] CAT5 Standard EIA/TIA T568B Wiring Diagram WAS RE: Patch Panels

Here's a guide I use for work.
 
Neil
 
CAT 5 Patch/Crossover Cable Creation Guide

Before you begin creating your CAT 5 patch and/or crossover cable, it's important to point out that the method outlined here is only one method. It is by no means the only or best method. Also, make sure you have all the necessary tools and materials before you begin. You will need a length of CAT cable, several RJ-45 connectors, and a crimp tool.
1. Most crimp tools have two blades: one designed to cut completely through a cable and the other designed to strip the cable jacket/insulation. Using the latter blade, strip the cable jacket/insulation back about an inch, so all the wires inside are exposed. Be careful not to cut the inside wires when stripping the cable’s insulation.
 
2. With the jacket/insulation removed, you'll find eight wires and a string inside the CAT 5 cable. Cut the string off, and untwist the wires back to within one-eighth inch of the jacket.
 
3. Fan the wires out from left to right in the order they are to be crimped. The crimping order depends on the type of cable you are making. For this guide, we will be wiring the cable to CAT 5 EIA 568B specifications. This is the configuration for a standard CAT 5 patch cable (See Table 1 and Figure A).
 
Table 1: How to wire a CAT 5 (EIA 568B) Patch Cable
Connector #1  Connector #2
 
White/Orange  White/Orange
 
Orange/White  Orange/White
 
White/Green   White/Green
 
Blue/White    Blue/White
 
White/Blue    White/Blue
 
Green/White   Green/White
 
White/Brown   White/Brown
 
Brown/White   Brown/White
 
Note: The first colour listed in the colour pair is the dominant colour of the wire. In other words, White/Orange is a white wire with orange stripes.
 
Figure A: Standard EIA/TIA T568B Wiring Diagram
 
See attachment FIG1.GIF
 
 
4. Grasp the wires firmly between your fingers and flatten them to remove their curliness. The wires must lay flat and together, aligned as closely as possible. Try not to get them out of order.
 
5. While holding them firmly, cut off about a half-inch of the exposed wires, so they are all the same length.
 
 
 
6. Slide the RJ-45 connector onto the wires, making sure the wires stay lined up. The connector has eight slots, one for each wire. Try to make each wire reach the end of its slot. The cable jacket/insulation should reach just beyond the end of the crimp point. If the insulation doesn’t reach far enough inside the connector or if the wires don’t reach the end of their slots, cut the wires off a bit more. If the cable jacket/insulation reaches too far past the crimp point, simply trim off a little more jacket/insulation.
 
7. Next, verify all the wires are in the correct order, and insert the connector into the crimping tool. Crimp it! This requires a little bit of strength, and you may need to use two hands.
 
8. Now repeat steps 1 through 7 for the opposite end of the patch cable, and you’re finished.
 
Creating a crossover cable
Crossover cables are used to connect two machines without the use of a hub, switch, or router. While similar to a standard CAT 5 cable, the wiring in a crossover cable is actually quite different. Instead of following the same wire pattern on both ends of the cable, one end is exactly opposite of the other, as seen in Table 2 and Figure B below.
 
Table 2: How to wire a CAT 5 Crossover Cable
Connector #1  Connector #2
 
White/Orange  White/Green
 
Orange/White  Green/White
 
White/Green   White/Orange
 
Blue/White    Blue/White
 
White/Blue    White/Blue
 
Green/White   Orange/White
 
White/Brown   White/Brown
 
Brown/White   Brown/White
 
Figure B: Standard and Crossover EIA/TIA T568B Wiring Diagram
 
See attachment FIG2.GIF
 
Note: Remember that these instructions are only a general guide. Your actual experience will depend on the tools and materials you are using.
 
 
 
 


For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


***********************************************************
This message is confidential and intended for the exclusive
use of the addressee(s) only and remains the property of
Exchange FS Group plc. You should not disclose its contents
to any other person. If you are not the intended recipient
please notify the sender named above immediately.

Registered Office: Munro House, Portsmouth Road, Cobham,
Surrey, KT11 1TE. Registered in England No. 2596452
***********************************************************

Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.