The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: NEWS - HomeVision Controls my Central Heating!


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: NEWS - HomeVision Controls my Central Heating!
  • From: "Mick Furlong" <dorsai@xxxxxxx>
  • Date: Sat, 15 Dec 2001 01:39:47 -0000
  • Delivered-to: mailing list ukha_d@xxxxxxx
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

I love it!
 
just one thing....if the system goes SNAFU and totally out of control then you could end up with a fried or frozen house.
 
This isn't my own idea but I have seen it somewhere...if you wire a couple of standard type dial therm thingys (damned if I know waht they are called but the thing you have to set the temp remote from the central heating controller) into the circuit you can allow frost protection and overheat protection. In effect all it does is cut out the HA system if temp is over x degrees or below x degrees.
 
I don't have the ability to design the circuit to do this but I am sure Mr. Guru Doxey does ;)
 
 
Cheers
Mick
 
-----Original Message-----
From: Mark McCall [mailto:mark@xxxxxxx]
Sent: 14 December 2001 11:35
To: ukha_d Egroup
Subject: [ukha_d] NEWS - HomeVision Controls my Central Heating!

HomeVision Controls my Central Heating!

14 December 2001

Submitted By: Mark McCall 

 

 

I've finished (eventually) the pics and write-up of Keith Doxey's interface between my central heating and HomeVision...

 

"The switch mounted LED's are fed >from Zone). HomeVision pulls Port A3/A4 low when the heating is OFF which short the LED side of the resistor to ground, this extinguishes the LEDs. The relays are fed from the 12 volt supply and are grounded by Port A1/A2 going low to operate the relay. This turns the heating ON. The mains side of the relays are wired in parallel to the existing programmer contacts and the programmer is set to OFF. In the event of HomeVision or Relay failure the existing programmer can be switched on and conventional heating control is instantly available. As the relays are connected to 240V AC is important that all connections are insulated using heat shrink sleeving and the enclosure containing the relays is only accessible by means of a screwdriver."

 

Click here to see all the pics, circuit diagram and write-up.

http://www.automatedhome.co.uk/homevision_heating.html

 

M.

 

 



For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Yahoo! Groups Sponsor
ADVERTISEMENT
See the Trailer!

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.